Does anyone know in what condition we need to tune the sensitivity adjuster of the sensor? Is it based on the size/diameter of the target?

More MC12059 ChungKarYee's questions See All

How to calculate the flow rate of water inside the piping using pressure?

Pressure is 2 bar and the pipe diameter is 2 inches

11 December 2017 6,930 5 View

What causes a magnetic contactor burnt?

Good day everyone, Is anyone knows why a contactor burnt ? It is a 220V and 50Hz magnetic contactor which connected with the oil circulation pump motor. thank you.

01 February 2017 2,995 0 View

What is the application for paper gasket?

Good day everyone! Is it suitable to use paper gasket for the thermal oil valve?

11 December 2016 5,539 1 View

What is VPN?

I have learned from website which said that I can change my IP address through VPN but I don't understand what is it and also is it safe ?

10 November 2016 8,368 2 View

Hi, what to do if error message always appear when running simulation using ANSYS fluent?

Currently running simulation using ANSYS fluent with time step size = 0.01 and number of time steps = 360000. (In reality i have to carry out the process in 1 hour, so 360000 times 0.01 equal...

04 May 2016 4,223 3 View

Hi, anyone know how to restore the license file to default format?

Hi, i not carefully open the license file in notepad and i can't find a way to restore it into default format. I have try use the 'regedit' method but still the icon still is in notepad form. Does...

02 March 2016 4,559 0 View

Anyone know how to create 2D using Autodesk Simulation CFD 2015?

Hi good day to everyone. Recently i'm trying to construct a 2D model using Autodesk Simulation CFD but i failed so i wish to get some guidelines from you all on how to create the 2D model in...

02 March 2016 5,192 5 View

Anyone know how much power(watt) of electrical heater that will be required to generate heat which can achieve 400 degree Celsius?

Hi, currently i try to figure out what kind of heat sources that can be used to heat the plastic to 400 degree Celsius and the amount of power(watt) that needed to consume in order to reach and...

01 February 2016 2,962 4 View

Hi, anyone know what is the factor of safety of mild steel?

AISI 1018 mild/low carbon steel has excellent weldability and produces a uniform and harder case and it is considered as the best steel for carburized parts. AISI 1018 mild/low carbon steel offers...

10 November 2015 7,788 3 View

What kind of bearing is suitable to support applied load of 1000 lbs ? Is there any other factors that we need to consider when selecting a bearing?

Hi everyone, the provided link is some information related to the bearing.

09 October 2015 9,594 7 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Any direct measurement to measure the bacteria or micro organism using IOT or any indirect measurement?

need of sensor details or sensor development for this question.

28 July 2024 4,539 3 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Mina Younan

https://www.ia.omron.com/products/family/407/lineup.html

Med Benyezzar

The datasheet show where to adjust the sensitivity (Screw on top, one turn in total). If your target is not very reflective or it is placed further away, then the sensitivity may have to be be set higher. Connect and test first and check that it is stable during operation (see indicator on top).