What are various Crack Parameters in ANSYS?

More Udit Singhal's questions See All

Where can one download data (csv, excel) for average daily values of AQI (air quality index) in popular cities, like, Delhi and Mumbai in India?

Air pollution has become a very big problem in Indian cities, especially Delhi. It requires immediate attention and we need to soon understand the trends, provide forecasts for future, issue...

19 November 2020 1,433 3 View

How to generate a Force which has a duration of 0.3 ms and allows excitation of waves of frequencies up to 80 kHz in matlab.?

Actually this is the impulse force, which is to be applied on the rod element?

09 September 2020 8,080 3 View

Absorption vs Excitation - Difference in setup?

I am using microspheres to create optical crystal patterns on a glass substrate. The source is halogen lamp and detector is a CCD camera both on opposite side of the substrate. I see a broad...

03 August 2020 7,924 6 View

IRS mission Thermal Imaging?

Hello, Anyone aware of any Indian Remote sensing Satellite having Thermal sensor (for UHI effect)? Data is free or paid?

24 September 2019 2,062 5 View

How to monitor selectivity of specific biomolecule in a mixture via potentiometry technique?

My work is on biomolecule sensing by potentiometry (CA, CV, etc.). Concentration of each individual biomolecule can be easily monitored by variation in current or voltage, but how to check...

12 February 2018 2,320 2 View

NCBI ORF finder has a limit of 50k bases, is their any other online software that predicts ORF without any limit for input nucleotides?

I donot want to use linux based tools and would like to know if such a tool is available for windows.

09 October 2017 978 1 View

What can we do if the Correlation matrix, during factor analysis turns out to be Non-Positive Definite (NPD).

Sample size < 50 No. of Items = 38 KMO barletts test is not appearing.

19 June 2017 9,541 3 View

Is there any real/sample data of online e commerce transactions available for research purposes?

Sample data set if available

16 February 2015 3,576 12 View

Can anybody tell me most optimization technique in solar cell for getting higher efficiency?

02 February 2015 7,727 5 View

How do you do generation scheduling in a deregulated environment?

In a generation scheduling problem, the load demand has to be satisfied but in a deregulated environment, GENCOs no longer have an obligation to satisfy the load demand. So, how is the system...

15 November 2014 684 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Mohannad H. Al-Sherrawi

Dear Udit Singhal

This link may be helpful

https://www.sharcnet.ca/Software/Ansys/17.0/en-us/help/wb_sim/ds_crack_overview.html

Silvio Rabbolini

The J -integral depends on the contour you are using to calculate it. You experience convergence if the plastic zone around crack tip is fully included in the domain you are considering. The mesh around the tip should be refined in order to accurately model the singularity and the stress/strain gradients. I suggest this report:

https://www.researchgate.net/publication/316927229_Computational_fracture_mechanics

Technical Report Computational fracture mechanics