What are values of *potential in abaqus?

More Vibhor Malviya's questions See All

How can I define circular tool-path in Abaqus-CAE?

I am simulating single point incremental forming and intend to get the profile "truncated-cone" on sheetmetal. How do i define the tool-path for this? For profiles like truncated-pyramid, when...

02 March 2015 2,734 8 View

Can one suggest what might be wrong with the analysis on Abaqus, as the sheet is not showing any plastic deformation even after 4mm depth of cut?

I am simulating Single point incremental forming on Abaqus CAE. Analysis completes successfully but i am not getting any plastic deformation on sheet. I gave an absurd value of 4mm depth of cut...

02 March 2015 7,242 8 View

How to reduce analysis time on Abaqus?

My model is taking 12 hours to complete analysis and i have defined just one step. Each step is of roughly 150 seconds and i have atleast 12 such steps. So, i need general tips, such as increase...

02 March 2015 5,661 8 View

How do I correctly specify a part as rigid body in Abaqus CAE?

There are two parts in model, a sheet and a tool. I defined tool as rigid body using constraint manager. By doing that I get a warning. warning: "Each of the nodes in node set...

01 February 2015 1,450 18 View

How can I resolve initial overclosures between contact surfaces?

Software : AbaqusCAE. For Sheet-tool contact surface, there seems to be some error in interaction property definition. The process I am trying to simulate is single point incremental forming. The...

01 February 2015 2,578 6 View

How can I define displacement boundary condition and amplitude in Abaqus CAE?

I need to move the tool along negative y-axis for which I have given value of U2:-150 (mm) and in amplitude: tabular I gave as time/amplitude as 0/0 and 1/1. Also, in the second step, displacement...

31 December 2014 3,562 12 View

Can anyone help with tool path definition on CATIA?

Kindly help me with tutorials on tool path definition. I am working on simulation of incremental sheet metal forming. I need to learn how to vary the forces exerted by tool in horizontal and...

08 September 2014 3,930 6 View

Which is the most accurate finite element program for analysis of incremental sheetmetal forming?

Many commercially available pre-processors and solvers for finite element analysis of forming operation are available. Incremental forming being an unconventional forming method, there are no...

07 August 2014 267 6 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View

Hamida Darwish

There are many papers found, Please use this website hope there is your answer,

[https://scholar.google.com/scholar?q=What+are+values+of+*potential+in+abaqus%3F+&btnG=&hl=en&as_sdt=0%2C5]

Jj Lee

hi, have you figure out how to define the symbols? If yes, do you mind to show me some hints?

皇銘 Chen

Can you explain in detail?

If R11 is set, how is the stress strain diagram in the 11 direction described?

my mail:[email protected]

thank