In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How do you integrate the 'friction' variable Xi in the Nose - Hoover Thermostat in order to apply it to a molecular dynamics simulation?

Everything tells you the derivative of Xi, but not how integrate the value to implement it into a simulation. How do you do this?

21 February 2021 6,481 1 View

How to implement boundary conditions in Abaqus contact problems?

Hello I am trying to simulate crawling motion of a bilayer beam using Abaqus. Kind of similar to this: https://youtu.be/os-Z3ucoFpA I am using multiphysics enabled (diffusion, deformation,...

20 February 2021 2,916 1 View

When to use Darcy or Fanning friction factor in frictional pressure drop measurement?

04 February 2021 6,174 3 View

What is the importance of create interfaces in 3D plaxis analysis?

While you analyse the stone columns in 3D plaxis, the interface should be used. What is the importance of that.

26 January 2021 2,440 4 View

Anybody to help me with Code source for DOUBLE CONCAVE FRICTION PENDULUM BEARINGS Please?

Hello, would you please share the codes for Base Isolation of structures using Double Concave Friction Pendulum Bearings? I am doing a related research but as I am just a beginner in MATLAB, I...

18 January 2021 6,683 1 View

FEM modeling of Joints/ Connection?

The attached Joint.png showed and example case of a joint (2 continuum members are connected). There are 3 characteristics of this, 1. There is a Gap: Cause small amount of rigid body rotation and...

07 December 2020 6,603 3 View

Can anyone help me with modelling of cyclic triaxial test in plaxis?

I am planning to do as axis symmetry case. But which model would be more appropriate for modelling strain controlled cyclic triaxial test on both silty sand as well as polymer treated silty sand?...

04 December 2020 8,522 4 View

How can I represent contact with cohesive behavior and friction in abaqus?

Hi, I am trying to represent an experimental test of pull out in abaqus, I have managed to get the detachment behavior (first section of the graph) but the part where the fiber slides does not...

30 November 2020 6,474 3 View

How to model Rainfall on sandy Soil or Slope using Python?

I had done some research in the field of rainfall simulation on sandy slopes, I did some tests on Laboratory and I did some modeling via Plaxis's Plaxflow module, I wanted to know if there is any...

29 November 2020 1,154 2 View

How to determine Friction coefficient in orthgonal milling?

I have used a Pin-on-disc tribometer to find the friction coefficient. However, now I am getting feedback from some seniors that I need to get a friction coefficient from orthogonal milling. There...

15 November 2020 8,151 9 View