In FSW welding simulation in Abaqus, I need some articles to check the difference between friction application methods (penalty - kinetic friction and static friction).
See attached article
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,504 0 View
I need help for my thesis.
24 May 2024 8,864 0 View
I need standard laboratory methods for washing glass and polyethylene containers in the soil laboratory With the best wishes Sajad Bayat
13 May 2024 5,244 0 View
If you are a researcher working with chaos and chaotic systems, which unsolved problem or question you have in mind Here I have collected some open problems and questions related to chaos and...
28 April 2024 8,493 2 View
For thermal analysis of FSW magnesium alloy welding by SPH method in Abaqus software, I need static friction coefficients - kinetic friction and Decay coefficient. Can someone help me how to get...
22 April 2024 3,944 1 View
I do the thermal analysis for friction stir welding in Abaqus software with SPH model. The problem I have is that the temperature of the particles is higher than the melting temperature of the...
20 April 2024 7,575 0 View
I am doing the thermal analysis of FSW welding. The heat transfer coefficient is applied on the surface, but our SPH part is meshed, how can I apply this coefficient? After finishing the analysis...
04 April 2024 6,325 2 View
05 March 2024 6,462 2 View
Hello Can someone help me how to apply the convection coefficient in FSW welding simulation in Abaqus by SPH method? This coefficient is applied to the surface and we have 90 in SPH, how can I...
03 March 2024 6,319 0 View
The problem I have is one is the high temperature of the part, how to solve the problem with the difflux subroutine, and the other problem is how to apply the convection coefficient for the SPH...
25 February 2024 1,638 2 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,167 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?
10 July 2024 8,762 0 View
we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...
30 June 2024 5,942 2 View
I am using apparent heat method for simulation
14 June 2024 4,669 1 View
I conducted a tensile test to analyze the strength of a welded joint and to implement an FEM model. Due to the high hardness of the base material, slippage between the grip and the base material...
10 June 2024 5,734 6 View
I want to realize a auto-analyze process for weld fatigue by fe-safe software. However, I found that the current.macro in Tools can not record the commands of the GUI operation about defining the...
04 June 2024 5,088 1 View
Hello, I have modeled a steel conical roof in Abaqus. Now I want to model the location of a groove weld in Abaqus in a spiral pattern from the bottom to the top of the roof. How should I model...
04 June 2024 9,833 1 View
I am trying to simulate the above truss in Abaqus to get its natural frequencies through Modal Analysis. The joints are connected through welding. However, I am unsure how to define the...
04 June 2024 4,071 1 View
I want to do modal analysis on a body which has two components which are in dynamic elastic and frictional contact with each other.
04 June 2024 8,493 6 View