Where to find Johnson-Cook parameters for pure Zinc?

22 May 2024 0 2K Report

I am currently simulating the impact of a zinc interlayer between Aluminum workpieces in ABAQUS (Friction stir welding process).

While it was easy to find in literature the Johnson-Cook parameters for Aluminum, I am not able to find the J-C parameters for pure Zinc.

Do you have any articles to suggest? Or somewhere to look for?

Thank you,

Best Regards

Badges
Science topic

Similar topics
Filing

More Ashu Kumar's questions See All

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,309 7 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

What is the relationship between the threshold voltage and the device's noise performance, particularly in terms of flicker noise and thermal noise?

The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...

29 July 2024 3,246 0 View

How we can use lattice-based cryptography for construction of S boxes?

Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.

24 July 2024 6,291 4 View

What is the solvent system required to run tlc for calixarenes?

If you don't understand my question let me know

21 July 2024 563 1 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

How to calculate corrosion rate from potentiodynamic polarization test data for dissimilar welds?

we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...

30 June 2024 5,943 2 View

Are there different databases similar to the Zinc database or how can I solve this problem in the Zinc database?

We were using the Zinc database for the virtual compound library in our studies, but there have been problems downloading a large number of compounds for a while. Are there different databases...

30 June 2024 8,144 1 View

What is the most accurate way to determine the energy gap of semiconductor materials? Is it better to use UV-Vis or PL measurements?

When preparing hierarchical zinc oxide ananostructure, the energy gap measured by PL was equal to (3.26 eV) While the energy gap value was determined by UV-Vis measurements (3.5 to 3.7 eV)

26 June 2024 7,505 6 View

Why my mesh convergence is failing in ABAQUS?

I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...

23 June 2024 9,080 0 View