How to deal with computed negative inflows in dams ?

This question aims to explore, from the part of expert colleagues, some methods that can be used to adjust the negative inflows calculated for the dams.

14 December 2019 1,486 3 View

How to choose reviewers for your submission ?

Most of journals require for paper submission to suggest three or four reviewers. How to choose them ? Is it among the authors of the papers cited in your manuscript, among the members of the...

09 September 2019 8,943 2 View

What is the best pipeline design software?

Hello i am looking for a software which can be used to design pipeline for a heating system. I need it to study the stress in pipes etc... Any software which could be tested with a free version...

28 March 2018 3,778 3 View

About the Protein extraction and purification?

Dear Researcher Please, If that possible to extract and purify a protein from SDS page Gel staining with coomassie Bleu. Many thanks

11 January 2017 1,049 4 View

Does anyone measured composite layers engineering constants using DIC for SHPB specimens?

26 December 2014 3,403 2 View

How can I analyze cell staining images using Fiji / ImageJ?

I have several fluorescent microscopy images for cell staining using three channels. Can you please suggest some methods to analyze these images?

05 May 2014 4,270 2 View

Can anyone help with MTT assay results?

I applied a MTT assay for A549 cell lines treated with different concentrations of Aluminium Oxide, I got the data from the plate reader, but I can't decide if my results are good or not ? And is...

30 April 2014 8,508 6 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View