What are the Behind The Meter cost components either capital or operational?

05 September 2022 0 1K Report

Is there any good reference for modeling the cost components of a BTM commercial battery with different power and duration scales?

Badges
Science topic

More Seyedeh Narjes Fallah's questions See All

How can I use proc nlmixed for two-level joint model for data that is not longitudinal?

11 May 2024 4,239 0 View

How to measure bond disscoaition energy of ReaxFF with lammps?

Hello, I have a script changing the distances of two bonded atoms and I calculated the total energy (or potenial energy, kinetic energy is zero) with energy minimisation tool of lammps (ReaxFF...

27 March 2024 4,468 2 View

Difference between output power variations of (Pd - coated) and (Pd-Cu -coated) tapered optical fiber?

Output power changes on the optical fiber sensor for hydrogen gas have been illustrated. Why does the Pd-Cu sensor show no sensitivity at low hydrogen percentages while the Pd sensor does? Why...

01 January 2024 2,200 2 View

Change in multiple band gap of CuSe after Ni-doping?

The band gap results for CuSe and Ni-doped CuSe, according to the Tauc plot and the mathematical DITM (Derivation Ineffective Thickness Method) model, in which thickness and type of transition...

29 December 2023 614 2 View

Conceptually, why is the energy of a hole considered greater than that of an electron?

We know that electron mobility is higher than hole mobility because the effective mass of an electron is less than that of a hole. However, if we ask why the effective mass of an electron...

14 December 2023 3,546 11 View

EDX result of sputtered tapered optical fiber with palladium and copper.?

Why are other elements such as calcium, oxygen, sodium, magnesium, aluminum, silicon and molybdenum visible in the EDX spectrum of tapered optical fiber (SMF‐28) covered with palladium and copper...

01 December 2023 7,414 4 View

Lower crystal quality together with lower band gap after annealing?

Why is it that after annealing, while the size of the particles has become smaller and the crystallinity has decreased with XRD, and the electrical conductivity has decreased, but the band gap has...

21 October 2023 5,950 4 View

A defect or something else in the AFM image for ZnO thin film prepared by sputtering?

What could be the reason for this situation in the AFM image? Is what is marked a DEFECT? and why. This is an image (AFM) for ZnO prepared by Sputtering method with -200 V as bias voltage and...

20 October 2023 7,855 4 View

I need my ID on the site, but I don't understand what it is?

Hello, I need my ID on the site, but I don't understand what it is?

22 August 2023 8,228 0 View

How can get rid of bubble formation during the butyl adhesive injection via Graco Supply Systems which are suitable for pumping viscous compounds?

We are producing the PE based insulator of door panels for automotive industries. In order to waterproof the doors, the butyl adhesive must be extruded around the insulating foams. While butyl...

04 July 2023 6,703 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Are there any commercially available Donkey anti-Alpaca secondary antibodies?

Are there any fluorescently labeled anti-Alpaca secondary antibodies raised in Donkey? So far I have only been able to find anti-Alpaca secondaries raised in Goat. Or is this not possible due to...

04 August 2024 4,255 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View