RDF calculation of water inside the Carbon nanotubes?

I am trying to calculate the rdf of water molecules present inside the Carbon nanotube. I tried to do the indexing first using gromacs tool gmx selection. But when it comes to calculating rdf, I...

17 February 2021 1,066 3 View

Correlation plot between Gene of Interest and miRNA?

Please suggest portals to retrieve normalized-quantile expressions of micro-RNAs (in RPM).My aim is to construct a correlation plot between the gene of interest and microRNA. I searched in human...

28 October 2020 6,398 3 View

Hello Can anyone suggest a good way of inducing oxidative stress in mice to exhibit proteinurea phenotype in the mice?

Hello Can anyone suggest a good way of inducing oxidative stress in mice to exhibit proteinurea phenotype in the mice or a good method to induce oxidative stress in the mice to study kidney...

26 July 2020 2,999 3 View

What is the relation between lattice parameters and particle size in manganites??

The change in particle size is resulting in change in unit cell lattice paramaters in manganites. Please explain it in terms of crystallography and why is it so.

28 February 2018 1,590 3 View

How can we interpret LC MS data?

I have TIC, EIC and MS data. How to create a library of compound in my plant extract?

21 December 2017 1,418 4 View

Single cell sort of adherent and suspension cells does not yield similar results. Any suggestions?

I am expressing GPCR in CHO cells, in suspension and adherent format. But when single sorting the cells using FACS Aria, i have obtained clones for the suspension format, but the adherent format...

26 September 2016 1,840 3 View

Can anyone help me explain what a hazard ratio of 20 means? Is it acceptable to have large HR values?

15 May 2016 8,894 5 View

How to remove high intensity pixels with other low intensity neighboring pixels in colored image?

10 April 2016 8,454 5 View

What is the minimum amount of papain (23500 Da) that I can see in the SDS PAGE gel?

I am performing reaction between iodoacetyl-PEG-biotin (linker) and papain. Thiol group of papain reacts with the linker to form a thioester bond. then I use streptavidin beads to fish out papain...

28 December 2015 4,814 3 View

Setting up a lab for human DNA extraction?

I am trying to set up our lab for human DNA extraction from brain tissue and CSF. Any suggestions on how to go about setting up a clean room to prevent any external contamination from bacteria,...

03 September 2015 4,581 3 View

Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View