Can any body tell me how to start simulation of water nucleation using COMSOL Multiphysics?
what do you mean by water nucleation? See if it helps:
Droppletevaporation_GANDHI-THESIS-2017
https://rc.library.uta.edu/uta-ir/bitstream/handle/10106/27216/GANDHI-THESIS-2017.pdf?sequence=1
Many thanks Gino,
I meant water evaporation>
Hello Ahmed,
You may be try to use the Laminar Two Phase Flow, Moving Mesh interface as a start of your simulations. you can try the following video:
https://www.youtube.com/watch?v=Lhn4dlWFmR4
Try also the Comsol modelling guidelines, It might be helpful.
Kind regards
Hayder
Many thanks Hyder.
Hi Ahmed,
You should try the Laminar flow module with multiphase flow. I am attaching a Youtube video. You can also watch the tutorials from the website of COMSOL. Hope this will work.
https://www.comsol.com/video/introduction-to-simulating-multiphase-flow-with-comsol-multiphysics
Regards,
Saif
I am working to simulate axial pump with inducer using CFD fluent and I need help to known how can create axial pump that mean how can rotate impeller with fixed the pipe wall under transient...
01 February 2020 8,827 3 View
Dear researchers I am going to teach a course on desertification but i need a help and somebody to share with me his/her experiences on teaching such a course. I would like to learn some teaching...
31 December 2019 2,384 4 View
I am working on concentrated to model journal bearing therefore I need to simulate it using Fluent CFD. I need to help me to create, mesh and setup this journal bearing please how I can to do this...
11 December 2019 7,564 2 View
Dear All, I am looking for an online course or website teaching the principles of molecular dynamic simulations. In specific, generating protein-protein and/or small drug-protein docking models...
10 November 2019 8,258 3 View
Hello! I'm trying to determine the pH of a cell culture plate using phenol red present in the medium (MEM) and a plate reader. However, phenol red's absorbance changes depending on the pH. Is...
05 June 2019 7,514 2 View
I am looking for a map in the resolution of Geological Formations, not according to the age of deposits in the format of shapefile or good resolution image. Thank you in advance.
01 February 2019 2,419 1 View
I need accurate details for the purpose of conducting some technical tests that concern some of the problems facing the research
10 November 2018 1,315 4 View
I am looking for material with high thermal capacity, which is cheap and could be used in concrete and blocks?
10 November 2018 1,726 3 View
I need to know if my column which i used in the analysis with high efficiency or no.
10 November 2018 9,014 0 View
28 October 2018 6,989 4 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View
I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...
23 February 2021 4,050 1 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View
How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?
22 February 2021 5,408 1 View