I want to simulate journal bearing using Fluent CFD?

More Ahmed Ramadhan Al-Obaidi's questions See All

Can anyone provide me geometry of an axial pump with induced with mesh and setup using CFD fluent?

I am working to simulate axial pump with inducer using CFD fluent and I need help to known how can create axial pump that mean how can rotate impeller with fixed the pipe wall under transient...

01 February 2020 8,827 3 View

Does anyone teach a course on desertification?

Dear researchers I am going to teach a course on desertification but i need a help and somebody to share with me his/her experiences on teaching such a course. I would like to learn some teaching...

31 December 2019 2,384 4 View

A request for an online course in principles of drug-protein and protein-protein molecular dynamic simulations?

Dear All, I am looking for an online course or website teaching the principles of molecular dynamic simulations. In specific, generating protein-protein and/or small drug-protein docking models...

10 November 2019 8,258 3 View

Is there a quantitative measurement of pH in cell culture using Phenol Red spectrophotometry?

Hello! I'm trying to determine the pH of a cell culture plate using phenol red present in the medium (MEM) and a plate reader. However, phenol red's absorbance changes depending on the pH. Is...

05 June 2019 7,514 2 View

Is there a website to obtain a Geological Map of Saudi Arabia (as shapefile)?

I am looking for a map in the resolution of Geological Formations, not according to the age of deposits in the format of shapefile or good resolution image. Thank you in advance.

01 February 2019 2,419 1 View

I want to know how nanomaterials can be used to get rid of oil contaminants?

I need accurate details for the purpose of conducting some technical tests that concern some of the problems facing the research

10 November 2018 1,315 4 View

What is the most suitable high thermal capacity materials for concrete?

I am looking for material with high thermal capacity, which is cheap and could be used in concrete and blocks?

10 November 2018 1,726 3 View

How we can know that the column used in HPLC has a good efficiency through the shape of peaks in chromatogram?

I need to know if my column which i used in the analysis with high efficiency or no.

10 November 2018 9,014 0 View

Two-Phase Flow?

Can any body tell me how to start simulation of water nucleation using COMSOL Multiphysics?

09 October 2018 5,901 5 View

Hi all, please I am quite confused regarding what is the difference between Effectiveness vs Functionality in Computer Science (Network Security)?

Well, after some researches I got that understanding: we can measure the Effectiveness of the security system through analyzing its works without facing the system to any threats or attacks. And...

07 August 2018 2,462 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to add a journal?

I would like to know how to register the journal Flora Montiberica (ISSN 1138-5952 - eISSN 1988-799X) in Research Gate.

02 March 2021 8,156 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Is it possible to remove a preprint posted by a journal which is already rejected?

As we know many journals are posting preprints (DOI) in advance before the peer-review process. However, there is no guarantee that the preprints get published. The journal's reviewers undergo the...

01 March 2021 5,778 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

No title

Hi, I have several doubts about one paper (Systematic Literature Review) that was rejected. The main topic is Single-Board Computers in engineering education during the period 2010-2020. The...

01 March 2021 9,015 3 View