Hello Everyone.
This might be very easy but I cannot figure it out whats wrong.
Equivalent visosity:
"((mus)*(TTl)"
It turns to yellow text>> unexpected unit of input.
>> (mul and mus are in [Pa.s]Tm is melting temp =1798[K]
((mus)*(TTl)
I think that flc2hs expects no unit. If you do a logical expression as you show at the end it probably won't go yellow.
I think you need to do something like
to get a black expression.
René Christensen : Thank you so much. It worked. Although, there should be no [K] multiplied to 1000.
Oh yeah, it should Pa s.
Yes :) Thank you once again.
Akash Meena You're welcome
Dear René Christensen ,
One small extended quetion on flc2hs function.
(flc2hs(T/1[K]-Tm/1[K], 20)
Tm is 1798K
1-2) I have attached one figure, how flc2hs is different from the step function ?
3) In the 3rd figure, could this flc2hs funtion shape ? If the 1st figure is right, how can I draw this 2rd figure flc2hs function ?
Regards,
Akash Meena
If the magnetic direction of any two black holes is made equal. So the capacity of attraction decreases to zero? If it becomes zero. So we can make the ability to magnetize / attract other...
22 December 2020 3,062 4 View
In a network, I want to set the buffer size of a device and then measure the number of packets in the buffer queue. The number of packets in the queued, dequeued an dropped, I need to calculate...
12 September 2020 4,654 4 View
Hello Everyone, I want to apply fresnel absorption in my laser keyhole welding model. I have seen fresnel equations on the COMSOL websites. It's kinda different from the one I see it in the...
08 September 2020 9,943 1 View
17 August 2020 174 3 View
07 July 2020 10,020 5 View
When we go for measuring of geometric mean enzyme activity as per the procedure of Paz-Ferreiro et al. (2012). before calculation of GMEA is it necessary to convert all the parameters in same unit.
01 July 2020 1,772 1 View
Hello Everyone, I want to write the expression for interface normal. How can I write it? Cannot find it properly in "Equation view". Please see the attched figure. Please comment if someone...
13 June 2020 5,464 3 View
Anyone if you know the BET surface area of nano-rod shaped ZnO nano-particles than please comment. The nano rod-shaped ZnO nanoparticles are synthesized by chemical precipitation method. If...
25 May 2020 8,856 1 View
Hello everyone. I want to apply the Heaviside function on the delta(phils) as shown in the figure. Can I apply the step function as a Heaviside function shown in the figure?
19 May 2020 310 7 View
which solar cell technology is more efficient for 400nm-1600nm diffused solar radiation and why?
27 April 2020 3,969 3 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...
25 February 2021 8,053 5 View
What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?
24 February 2021 8,219 2 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View