01 January 1970 2 1K Report

Hi, I need to configure the ScanWave of Xevo TQ-S, when I run a MRM method, I select an option called PIC, and then the option of ScanWave DS is eneable, however when I finish the set up appers an dialog box that said "ScanWave PIC selected, ScanWave optimization not loaded, please ensure a suitable optimization is loaded before acquiring.", and the I try to configure in everywhere with out succesful, please, someone knows how to do the optimization

More Carlos Joel Salas-Montantes's questions See All
What does a decreasing 𝐶𝑒 vs. 𝑄e ​plot indicate in an adsorption isotherm?

I am conducting adsorption experiments in a liquid medium, and one of my samples showed a decrease in Qe​ values with an increase in Ce​. Has anyone encountered this behavior before? What does it...

26 June 2024 7,304 2 View

Expert in advanced statistics interested in contributing to an academic article on the adoption of digital innovations in agriculture?

We are looking for a highly qualified researcher with expertise in advanced statistical analysis to contribute to a scientific article to be submitted to a prestigious journal by the end of the...

13 June 2024 569 4 View

Word error in a title / full text (1 page) shared: may I correct it ?

A recently published visual abstract should have the title "Word First Myelography..." instead of the error "Mielography". (the 2 other text references in the article are correct) I am changing it...

20 May 2024 8,134 1 View

Fluorescence spectroscopy: signal from water?

In order to proceed with the quantification of an Azide Alkyne Cycloaddition reaction efficiency by using a fluorogenic probe with Cy5-DBCO, I first need to construct a calibration curve. The...

16 May 2024 6,266 5 View

Is there a commercially available cell line from human cancer-associated fibroblasts (CAFs) isolated from malignant pleural mesothelioma or lung ca ?

Dear community, I am currently working on a proposal focusing on cancer-associated fibroblasts (CAFs) from malignant pleural mesothelioma (MPM). In my search among commercial cell line providers,...

05 May 2024 5,572 4 View

For DOM (dissolved organic matter) and in addition to the Follin method strategy, is there another way to determine phenolic content in the sample?

This is working with DOM (dissolved organic matter) and in addition to the acid-base titration strategy, Follin's method, there is another strategy to determine the amount of phenolic?

23 April 2024 2,197 1 View

Could you use a Tesla Turbine in a car?

In 1913, Nikola Tesla patented a new kind of turbine that required no blades and converted kinetic fluid energy into rotational energy. It uses nozzles that apply fluid to the edges of smooth...

17 April 2024 6,702 0 View

Where i can find calibration area used from my model ?

Hello, friends. Currently, I am working on species distribution modelling using maxent. I have run the model using occurrence and climate data from WorldClim. Where i can find calibration area...

14 April 2024 2,460 3 View

How can I reduce the variability of CFU counts between replicates?

I'm challenging bacteria with different compounds, then plating the suspension on LB agar to assess CFU and understand the bactericidal properties of my compounds. However, I'm encountering...

10 April 2024 7,459 7 View

[INFOGEST] In vitro digestion, how can the concentration of each digestion step be resolved?

Hello everyone, I am interested to know how I have to calculate the concentration of a specific analyte during the digestion steps (salivary, gastric, intestinal...). During the method, the...

04 April 2024 9,366 1 View

Similar questions and discussions
One product ion not detected in my tandem mass spec, why was it?

Hello, I am currently doing a method optimization for chloramphenicol using our lab's tandem mass spec. I have done Q1 scan (prec ion: 320.10 m/z) and did MRM scan for three product ion. Upon...

24 April 2024 250 0 View

How to choose optimal collision energy (CE) for MRM transition?

Hello all - I am new to learning MS and don't have a lot of guidance. I am having a really hard time finding information on what criteria is used to choose the optimal CE for an MRM transition. I...

26 July 2023 9,538 1 View

What is the possible peak at m/z = 535.8 for lycopene?

I am analyzing Lycopene using LC-MS. I use a C18 column and my mobile phase is Methanol: MTBE = 95:5. I use an Agilent Ultivo QQQ mass spectrometer with APCI negative ion mode. I see the precursor...

07 May 2023 525 0 View

Injections of QC standard yield increasing areas in negative ionization mode (LC/MS/MS)?

Hi all! I am using a Waters-TQS micro (LC/MS/MS) in negative ionization mode (MRM) to analyse a few compounds. When doing QC injections (i.e., repeated injections from same vial of standards at a...

30 November 2022 8,196 4 View

Can I quantify peptides by MRM approach of mass spectrometry without ion library in Skyline? Is it acceptable?

Typically, peptides are quantified by MRM by using softwares such as Skyline and Fragment ion library prepared by untargeted approaches are used for that. Is it okay if I quantify peptides...

13 November 2022 6,938 0 View

SIM and MRM mode in LCMS, which one is more sensitive?

I am currently developing a LCMS method for certain genotoxic impurity in API on a shimadzu 9030 qTOF LCMS. And I had an argument with my coworker about which mode is more sensitive, SIM or...

08 July 2022 1,861 4 View

If one Transition is sufficient for Quantification in LC-MS/MS method ?

I am developing an MRM method for multi-analyte quantification using triple quad mass-spectrometer. Shall I go ahead with single transition which is stable and most abundant for each analyte or...

04 July 2021 7,806 8 View

How to do survey scan or metabolite screening using LC-MS/MS in lipidomics?

In the field of Lipidomics or Metabolomics, how is the accurate method to achieve the comprehensive metabolite of a sample using LC-MS/MS? MRM method might be sensitive enough to achieve the...

24 May 2021 869 3 View

Which instrument is preferred to do untargeted metabolic profiling for a herbal plant?

In our lab, we are working on a herbal extraction optimation so that we need to understand the total profile difference between optimized and unoptimized extraction. Which that we have multiple...

14 September 2020 9,377 3 View

What is meant by 'Precursor' and ' Product' in MRM mode using GC-MS/MS?

In pesticide analysis I used MRM mode in MS method, and it asks about precursor and product. I used default values as precursor at 272 and product at 222 m/z for analyte I used Benomyl (a...

11 August 2020 7,740 10 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close