How can i simulate the wind turbine flow in 3D in any commercial softwares...ANSYS can be little helpful...Thank you
You can either use Multiple reference frame or sliding mesh analysis.
Create the Geometry of air foil in Ansys Gambit and then import in the Anysis fluent.
Dear friends !! I am designing wind turbine blade with multiple and single airfoil configurations as a part of my PhD thesis. I need to find the flow separation point in a wind turbine blade...
08 September 2017 8,718 3 View
Hey guys !! I have been working on Solid works for a heat exchanger model and now I need to mesh my surface. I couldn't able to import the model in the ANSYS 16 workbench. Kindly help me in this...
08 September 2017 9,564 12 View
Sirs In my study, I have modeled a wind turbine blade and meshed using ICEM CFD /ANSYS WB.. The subsequent cases involve Vortex generator to be incorporated on the blade surface and I request to...
10 November 2016 2,021 5 View
Sir I am designing a wind turbine blade with 3 airfoils integrated @ root,primary and tip.While modelling of blade I need to know the design angle of attack .How can I find the AOA for this type...
08 September 2015 4,694 2 View
Hello..My research is focused on Wind turbine flow control.I want to analyse the 3 bladed turbine with rotor assembly for a dynamic analysis.Ca anyone help me how to proceed with the analysis?I...
08 September 2015 8,690 7 View
I want to analyse a blade computationally and which solver can be used ? Is there any specific solver or depending on application it is selected? Suggest me
08 September 2015 2,435 10 View
I am involved in Energy Harvesting using Smart Structures .As a start-up I am extracting electrical response from PZT (Lead Zirconate Titanate) material subjected to a cantilever action.Now I have...
03 April 2015 439 6 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,728 6 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...
03 August 2024 888 1 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,510 3 View
Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...
29 July 2024 8,624 1 View
How to apply magnetic field parallel to b axis of any crystal
29 July 2024 4,083 2 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View