it is possible if anyone can recommend me some articles relating using SST turbulence model for different types of shapes where the fan is rotating inside.
CFD/CFX/FLUENT
hello ,
This is a paper that compares tow kinds of SST and Almeras i used for improving my study about vertical ansys wind turbine .
Hope Ive helped
Conference Paper CFD CALCULATIONS OF THE FLOW OVER A NACA 0012 AIRFOIL
thank you sir
I have with this UVA led light with the following specification. -Voltage = 3- 3.4 v DC - Power rating = 0.2 w/pcs -longevity = 35,000 hr light intensity = 400-500 mcd wavelength = 400-500 Nm But...
06 April 2016 1,953 2 View
I am currently doing a mosquito shape design analysis for the best suction pressure and velocity at the inlet caused by the fan. Assume the design is a nozzle. How do i go about selecting the...
24 January 2016 7,441 0 View
Any recommended articles or websites? Assume my computer fan is inside my model. How do i go about the calculations for CFM, Flowrate and Turbulence and the reynolds number. Assume air enters the...
16 January 2016 7,482 1 View
I am creating this nozzle design which have a varying fan speed. I will like to know if fan speed causes noise.
12 January 2016 1,493 4 View
Any articles available?
16 August 2015 8,137 7 View
How much heat is release in the recombination process? Please support with any evidence or journal papers. Require them for my final year project as reference.
11 August 2015 5,206 5 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...
02 August 2024 3,174 1 View