How can I fasten 3 or more layer of solid plates in ABAQUS by means of Fasteners?

I know this is possible but I don't know how to do?!

03 April 2016 8,985 1 View

How to make a ballscrew drive by means of connectors in abaqus which its input is torque and its output is linear motion. Is it possible? How?

I want to model this joint with connectors not by real modeling a ballscew drive.

11 December 2015 9,057 4 View

How can I verify or validate my dynamic analysis in abaqus: motion of a robotic mechanism with flexible parts (video attached)?

02 March 2015 7,037 8 View

Can anyone help me about time scaling factor in dynamic explicit analysis of Abaqus?

I'm doing an impact analysis in abaqus using dynamic explicit. Some times when the velocity of impact is high, the job aborts and I reduce the time scaling factor (=0.1) and it solves the problem!...

31 December 2014 3,465 11 View

How can we do fatigue analysis with cyclic step in ABAQUS which there are steel and rubber in the model as the materials?

I'm doing a fatigue analysis on a simple mount in ABAQUS which contains Steel and rubber as materials. Fatigue in the steel is important and the damage data is imported just for the steel. But...

01 January 1970 2,860 2 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View