How can I fasten 3 or more layer of solid plates in ABAQUS by means of Fasteners?

04 April 2016 1 9K Report

I know this is possible but I don't know how to do?!

can you explain your question a little further.

If you want to do static means ,you can straight away define the contact between master and slave surfaces and apply torque.

Badges
Science topic

More Amin Noorian's questions See All

Problem in modeling hydraulic cylinder-piston in Abaqus using CEL technique, can any one help?

Dear All I'm modeling a cylinder-twin piston containing water but the passive piston doesn't move in the effect of fluid pressure and motion. Actually the right side piston has a velocity and the...

11 December 2019 7,267 0 View

How to make a ballscrew drive by means of connectors in abaqus which its input is torque and its output is linear motion. Is it possible? How?

I want to model this joint with connectors not by real modeling a ballscew drive.

11 December 2015 9,306 4 View

How can I verify or validate my dynamic analysis in abaqus: motion of a robotic mechanism with flexible parts (video attached)?

I've imported a solid model of a parallel robot in abaqus and defined all the constraints, contacts, trajectories in joints and etc. It is moving reasonably. It's end effector has a little...

02 March 2015 7,274 8 View

Can anyone help me about time scaling factor in dynamic explicit analysis of Abaqus?

I'm doing an impact analysis in abaqus using dynamic explicit. Some times when the velocity of impact is high, the job aborts and I reduce the time scaling factor (=0.1) and it solves the problem!...

31 December 2014 3,903 11 View

How can we do fatigue analysis with cyclic step in ABAQUS which there are steel and rubber in the model as the materials?

I'm doing a fatigue analysis on a simple mount in ABAQUS which contains Steel and rubber as materials. Fatigue in the steel is important and the damage data is imported just for the steel. But...

01 January 1970 3,115 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View