Pressure profile in intake and exhaust case in ansys forte module.

Gopal Deshmukh @Gopal_Deshmukh2

01 January 1970 0 5K Report

what is meaning of pressure profile in intake and exhaust boundary case in ansys forte module.

Badges
Science topic

More Gopal Deshmukh's questions See All

Query regarding Sandia_Engine_LTC_EarlyInj.ftsim?

hi i need this tutorial files, Sandia_Engine_LTC_EarlyInj.ftsim. thank you

31 December 2018 9,017 0 View

Does anyone have ANSYS forte (18.2)Tutorial_ Inputs.zip file?

hi experts I don't have access to Ansys Portal. I need ANSYS_forte Tutorial_ Inputs.zip file to perform some tutorials (18.2). If someone has this file please send it to me. I shall be grateful....

31 December 2018 1,961 1 View

What is meaning in ansys forte cannot run MPIEXE ?

in ansys forte , when i give a mesh simulation command, it shows an error cannot run MPIEXE. how can i solve this problem. thank you

08 September 2018 5,641 0 View

Does anyone have tutorial and examples of AVL Fire diesel? n how to use software also?

Hi All, I am trying to learn avl fire diesel engine . i just don't know from where should i start. Can you help me find tutorials and examples of this software? and also, how to use this software?...

01 February 2018 8,174 2 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View