08 August 2014 1 3K Report

Any Modelling and Simulation software for Electronic Devices?

More Manoj KUMAR Parida's questions See All
Cross section of Uranium-238 at different fast energies of neutron?

Dear All, The neutron cross section of element generally falls with the increase in neutron energy. But in U-238 the fission cross section at Neutron energy of 1MeV is 0.3 barns whereas it...

02 March 2017 1,774 4 View

Ideality factor for diodes?

Is there any mathematical formula there for the ideality factor of the diodes? I will be very much thankful for the above. Please send the mathematical expression for it.

08 September 2016 7,007 5 View

The pulse shaping circuit of the radiation detector?

In the radiation detector the pulse shaping circuit consists of CR-RC circuit and amplifier.The function of pulse shaping amplifier is to improve Signal to Noise ratio.It also act as a filter to...

08 September 2016 8,565 4 View

How to reduce shot noise in the semiconductor radiation detector?

Generally there are three types of noise is present in the semiconductor radiation detector.These are Thermal Noise,Shot noise and Flicker Noise.The thermal noise is removed by operating the...

08 September 2016 9,355 2 View

Coating of Enriched Boon-10 on Si Surface other than CVD technique?

Dear All, Is there any technique other than the CVD to coat the Enriched Boron-10 on the Si surface? I will be very much thankful for the reply. Thanks & Regards Manoj

08 September 2016 8,686 0 View

In radiation detector Generally the HV Bias to the detector is given through the charge sensitive Preamplifier?

In the commercial available charge sensitive preamplifier  for semiconductor radiation detector.Generally the HV(High Voltage) bias given to the semiconductor detector  is  through the charge...

08 September 2016 4,154 4 View

Neutron irradiation effect on semiconductor PIN Diode?

I have performed the neutron irradiation on the PIN Diode. I have found that the forward bias cut-in volatge has been shifted. Why these shift been observed in the neutron irradiated PIN...

06 July 2016 8,002 3 View

Why electric field is maximum at the center of the depletion region in the PN junction?

In the depletion region only uncovered ions are exiting then why we have the maximum electric field at the center of the junction?

06 July 2016 7,472 6 View

How does a guard ring in the PIN Diodes reduces the surface leakage current?

The function of the Guard ring is to reduce the leakage current and make the PIN diode to work  at higher potential ? How does the guard ring perform this function? Please some one explain...

06 July 2016 6,690 2 View

Common mode signal calaculation?

Dear All, For the common mode signal the input voltage is calculated as (V1+V2)/2. Why we are calculating the common mode input signal as (V1+V2)/2 whereas in differential mode the input signal is...

04 May 2016 2,090 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close