Coating of Enriched Boon-10 on Si Surface other than CVD technique?

Manoj KUMAR Parida @Manoj_Parida2

09 September 2016 0 9K Report

Dear All,

Is there any technique other than the CVD to coat the Enriched Boron-10 on the Si surface?

I will be very much thankful for the reply.

Thanks & Regards

Manoj

Badges
Science topic

More Manoj KUMAR Parida's questions See All

Cross section of Uranium-238 at different fast energies of neutron?

Dear All, The neutron cross section of element generally falls with the increase in neutron energy. But in U-238 the fission cross section at Neutron energy of 1MeV is 0.3 barns whereas it...

02 March 2017 1,774 4 View

Ideality factor for diodes?

Is there any mathematical formula there for the ideality factor of the diodes? I will be very much thankful for the above. Please send the mathematical expression for it.

08 September 2016 7,007 5 View

The pulse shaping circuit of the radiation detector?

In the radiation detector the pulse shaping circuit consists of CR-RC circuit and amplifier.The function of pulse shaping amplifier is to improve Signal to Noise ratio.It also act as a filter to...

08 September 2016 8,565 4 View

How to reduce shot noise in the semiconductor radiation detector?

Generally there are three types of noise is present in the semiconductor radiation detector.These are Thermal Noise,Shot noise and Flicker Noise.The thermal noise is removed by operating the...

08 September 2016 9,355 2 View

In radiation detector Generally the HV Bias to the detector is given through the charge sensitive Preamplifier?

In the commercial available charge sensitive preamplifier for semiconductor radiation detector.Generally the HV(High Voltage) bias given to the semiconductor detector is through the charge...

08 September 2016 4,154 4 View

Neutron irradiation effect on semiconductor PIN Diode?

I have performed the neutron irradiation on the PIN Diode. I have found that the forward bias cut-in volatge has been shifted. Why these shift been observed in the neutron irradiated PIN...

06 July 2016 8,002 3 View

Why electric field is maximum at the center of the depletion region in the PN junction?

In the depletion region only uncovered ions are exiting then why we have the maximum electric field at the center of the junction?

06 July 2016 7,472 6 View

How does a guard ring in the PIN Diodes reduces the surface leakage current?

The function of the Guard ring is to reduce the leakage current and make the PIN diode to work at higher potential ? How does the guard ring perform this function? Please some one explain...

06 July 2016 6,690 2 View

Common mode signal calaculation?

Dear All, For the common mode signal the input voltage is calculated as (V1+V2)/2. Why we are calculating the common mode input signal as (V1+V2)/2 whereas in differential mode the input signal is...

04 May 2016 2,090 1 View

Tappering of channel in MOSFET with increase in Vds?

Dear All, Why there is a tappering of the channel at higher bias voltage of Vds in MOSFET?

04 May 2016 10,126 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the best method to detect the chemical composition of pollen ?

I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?

28 July 2024 5,331 1 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

Question about water vapor uptake of metal-organic frameworks?

I'm working on the atmospheric water harvesting, and i synthesized MOF by adding some materials into precursor and changing the conditions. (i followed Hydrothermal method) Actually, if MOF is...

24 July 2024 1,515 0 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View