Please recommend me the proper steps (blocking method) to generate Hexahedral mesh of the following geometry inside ICEM-CFD?

03 February 2021 1 1K Report

I am facing an issue while blocking for the geometry mentioned in the image. After blocking it ends with a triangular block due to its shape. How to create a hexahedral mesh for this geometry in ICEM-CFD?

Muhammad Ali

It is easy to model wind tunnel shape or surface, see e.g., Article Wind-tunnel and numerical modeling of flow and dispersion ab...

Article Analysis of subsonic wind tunnel with variation shape rectan...

Also see the attached pdfs.

Badges
Science topic

More Himanshu Banait's questions See All

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to create Component Model Synthesis in Ansys Workbench?

I have an assembly of parts. I want to reduce the number of modes of the individual parts by CMS.

11 June 2024 2,966 0 View

I am trying to do LCA of Water Treatment Technologies. Are there any recommended introductory resources or textbooks on LCA that you suggest?

Some Other Questions, if you can answer: What types of data are essential for conducting an LCA, and where can I find reliable data sources for water treatment technologies? How do you deal with...

11 June 2024 4,791 0 View

How to FE model from Modal analysis to use in Static Structural in Ansys?

I have two components for which I want to extract some number of modes shapes for each. Then using those model of the component I want to couple them together for non linear static analysis.

10 June 2024 1,234 0 View

How to create solid45 elements to an existing cad geometry?

I imported an 3D cad geometry in ansys. Now I want to create the mesh with solid45 element in workbench. How to proceed?

05 June 2024 2,490 1 View

Among Ansys and Abaqus which one is preffered for Modal analysis?

I want to do modal analysis on a body which has two components which are in dynamic elastic and frictional contact with each other.

04 June 2024 8,493 6 View

How can we reconcile the apparent contradiction between the statement "All productive soil are fertile" and "all fertile soil are not productive"?

19 April 2024 3,312 1 View

How to do the transfection by lipofectamine method? at what ration we will add lipo:dna?

lipofectamine method for the transfection in MDA-MB231 cell line

18 October 2023 3,311 0 View

How to claim authorship of article?

how to claim authorship of article?

08 September 2023 6,870 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

Are there always been barcodes, apapters and primer sequences in the FASTQ files of NGS?

Hello researchers, Sorry for my stupid question. I am learning the QIIME2 workflow for analyzing some 16s amplicon NGS fastq data. I found a very nice paper with data and code public available...

20 July 2024 5,405 2 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View