Perkin Optima 5300dv v8 error solution?

03 September 2021 0 2K Report

Hi all,

I am troubleshooting ISP analyser of Perkins model Optima 5300DV.

I am facing an issue.

It takes upto 3-4 hours in warming up. As soon as it's warming up time about to end, it gives indication of Argon gas. Next, when warming up completes, The software shows a V8 error.

Which is temp sensor not detected and temperature is very low.

Can anyone give some suggestions to get out of this issue?

Badges
Science topic

More Anees Ul Hasnain's questions See All

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

What strategy should be adopted to calculate topological indices efficiently?

Most of the time it is observed that in many manuscripts there are several typo error of topological calculation errors of calculation and partition of edges what ever the type of partitioning it...

22 July 2024 811 0 View

Why methanol and sulphuric acid used in the analysis of polyhydroxyalkanoates (PHA) by GC-MS?

Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?

22 July 2024 1,210 2 View

How can I define Planetary motion in ABAQUS CAE, how define motion of three rollers around a central axis and passive rotation about their own axis?

16 July 2024 4,145 1 View

How to load Remedesivir drug into mesoporous nanoparticles?

Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...

01 July 2024 889 3 View

What is the reason of appearance of 2 or 3 peaks in zeta potential analysis of sample?

Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...

30 June 2024 1,063 4 View

What is the best way to synthesize cDNA of miRNA; using poly A kit or stem loop PCR?

Recently, I have been trying to quantify the expression of miRNA. I have extracted the miRNA. However, I am not clear about using the cDNA synthesis kit usually there are two kits providing by...

16 June 2024 9,723 2 View

Which is the best media for revival of Pseudomonas aeruginosa?

Hi I am trying to revive Pseudomonas aeruginosa from frozen glycerol stock and also from cryobeads. But there was no bacterial growth. I used nutrient agar, tryptone soy agar to streak on. Also I...

09 June 2024 6,651 9 View

Gromacs first step of minimization ?

I have face this problem anyone help me how to solve this issue ?which is below Fatal error: There are inconsistent shifts over periodic boundaries in a molecule type consisting of 78 atoms. The...

07 August 2024 2,598 1 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

What is the mechanism of atmospheric pressure plasma Jet (APPJ)?

In general, the characteristic of electric current as a function of voltage in argon plasma jet using dielectric barrier discharge in atmospheric pressure, jet length will increase by the increase...

16 July 2024 9,316 1 View

Veeco Nanoscope IIIa Troubleshooting -- How to Fix Not Turning On?

My school recently acquired a Veeco Multimode and Nanoscope IIIa. While our software and computer is set up and working, the actual Nanoscope is not powering on. We currently have it wired up, and...

19 June 2024 592 0 View

P-nitrophenol acetate assay for esterase and media supernant colour interference. what can be done?

I am performing p nitrophenol acetate assay for esterase enzyme. My media contains a different concentration of peptone (0.5, 2, 5%) and after centrifugation the supernatant is slight yellow....

16 June 2024 4,381 0 View

Invasion assay troubleshooting MDA-MB-231 cells?

Hi everyone! I'm performing transwell assay for MDA-MB-231 cells, but surprisingly no cells invaded after 20h incubation. I don't have much materials so my troubleshooting experiments are...

15 June 2024 1,006 2 View

Facing issues when analyzing raw LC-MS/MS data with MS-DIAL?

I am facing a problem with my Waters MSe raw data. I have tried to open my raw data with AIF mode, after converting my file to ABF format for MS-DIAL, but everytime my system crashed. Later I...

14 June 2024 2,492 1 View

What's wrong with my iPSC cell morphology?

This shape gradually spreads. Even if you install new cells again, it will change like this at some point. Has anyone experienced the same thing as me? I tried using Matrigel again by aliquot it....

12 June 2024 7,269 5 View

GCMS troubleshooting: Shimadzu GC-2030 CAR1 AFC control irregularity E2134 error means leak in the system?

Have you encountered a CAR1 AFC control irregularity error with Shimadzu's GC instrument? Manual states that there is a problem with carrier gas supply and advises to contact service. Could not...

06 June 2024 2,373 1 View

[SOLVED] Philips SEM XL30 (Tungsten Filament): HT not working after pressure failure?

Dear fellow researchers, We are currently operating a Philips XL30 Scanning Electron Microscope (SEM) equipped with a tungsten filament and have encountered a significant issue. Recently, our...

28 May 2024 232 2 View