Can medicinal plants really play an inherent rule in the COVID-19 tackle?

Numerous scientific reports cited plant extracts with potential antiviral activity and even anti-COVID-19? Why these findings are neglected? I remember very well the warning released by the WHO to...

17 February 2021 2,141 9 View

How to incorporate a variable in damage model?

15 December 2020 7,284 2 View

Mathematical or computational modelling of protein oxidation?

I am looking for a research paper about the mathematical or computational modelling of protein oxidation (caused by reactive oxygen species).. I would really appreciate that if someone helps me...

17 November 2020 2,340 3 View

When i made an Autotune on GC-MS to check the apparatus, it's not continue the process and there a problem in Mass Filter Electronics?

Dear Connections, I hope you are doing well when I made an Autotune on GC-MS to check the apparatus, it does not continue the process, and there a problem in the mass Filter Electronics as shown...

10 October 2020 8,131 3 View

Can FEM model learn from experimental results?

I am looking for a research in which the finite element model was trained based on experimental results.

02 October 2020 9,277 19 View

Does anyone know what is an appropriate statistical analysis of drug release studies?

I am measuring the drug release of a few drug-eluting implants in dissolution medium in different time intervals. All the measurements are in triplicates. Would ANOVA or TTEST is an appropriate...

20 September 2020 8,183 5 View

Master thesis about the field of the luxury watch market?

18 September 2020 5,802 5 View

What is the proper solvent which used in liquid detergent to make it soluble?

Good afternoon everyone, I hope you are doing well I had several samples of liquid detergent I wanna to soluble it with a solvent. I tried with both of ( water, Ethyl alc., Parrafin Oil, DPG,...

05 August 2020 8,664 3 View

Is it possible for anybody to help me for fix bridge modeling in OPENSEES?

I modeled a two-span concrete box girder bridge base on FHWA design specification, and now I recognize a problem in modeling because my first period is higher than I expected. With initial...

12 July 2020 415 3 View

What is the best parameters in GC-MS for DB-WAX (60m*0.250mm*0.25microm) in the fragrances field?

Hi everyone, I hope you are well and stay safe. I am an operator for GC-MS instrumental and my company replace the column with another new one which called DB-WAX (60m*0.250mm*0.25microm). A...

14 June 2020 4,440 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How to remove unedited version of the manuscripts from research gate?

Our manuscript was published ahead of print. The edited and revised version is now available. How do I remove the old version of the manuscript from the research gate?

01 February 2021 5,965 1 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

How to add a single parameter in Ansys Additive Manufacturing Workbench parameter setting dialogue box?

Ansys 19.2 R2 and 2020 R1 versions of Additive Manufacturing Workbench is convenient for powder-based Additive Manufacturing processing. However, in this workbench, there is a machine parameter...

19 January 2021 3,017 2 View

How can I stain 3d printed cells in hydrogel without damaging the gel?

I tried staining my cells in a gel using standard protocols with 4PF% for fixation and triton-X or saponin for permeabilization but the gel always gets damaged throughout the steps, and at the end...

17 January 2021 4,170 1 View

Method to measure printed layer thickness on paper substrate ?

I want to measure thickness of screen printed graphene ink on paper substrate. Can anyone suggest any accurate and feasible method to measure it. I tried profilometry (stylus & optical) but...

11 January 2021 6,179 6 View

A three electrode sensor inkjet printed gets damaged in few hours of usage in a dynamic media flow chip, any solution for that?

We are using some biosensors which are inkjet printed and are used in the microfluidic chip where media is flowing at the flow rate of around 60 uL/min. However, after the continuous use of few...

05 January 2021 610 2 View

How to give port for printed log periodic dipole array antenna in CST?

PLPDA have radiating element on both sides of the substrate. so how to apply port. i have attached the figure below.

03 January 2021 4,005 6 View

I want to design a printed log periodic dipole array antenna on only one side of the substrate. is this acceptable one ?

actually for PLPDA, it is designed on both sides of the substrate for providing 180 degree phase shift between the elements

28 December 2020 3,148 3 View

How can I find my publication with the highest citation rate?

How can I find my publication with the highest citation rate in Research Gate? Is there a list of my publications? How can I print the list?

23 December 2020 8,476 12 View