Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Possible reasons for high bioavailability after I.M and S.C. routes...?

What should be the possible reasons if we obtained more than 100% bioavailability of antibiotics (marbofloxacin) after I.M. and S.C. routes of administration in cattle species.

16 February 2021 971 4 View

Is it mandatory to have a M.phil/MS or PhD degree for conductiong the Research in any field ?

I am confused here that is there need to have a M.phil/MS or PhD degree to condcut the research?

24 December 2020 250 3 View

Type of geometric/ trigonometric value in VPL mathematical formula?

the VPL formula can be given here as, f(P)=sum((a+b*P+c*P^2)+abs(e*sin(f(Pmin-P)))) Can anyone please explain if the value from the term (Pmin-P) in the above formula is in degrees or radians?

23 November 2020 9,961 2 View

Why Bryophylum Plant lower leaves turned yellow at Early arrival of winter. It is due to stressful conditions or nutrients problems?

Winter, Yellose, stressful conditions, nutrients unavailability, water unavailability. Pic attached. Bryophylum plant.

09 November 2020 8,526 8 View

How to define two phase change materials with different operating (boussinesq) temperature in cell zone conditions of FLUENT?

Hello, i am trying to simulate two PCMs in a domain. I assigned their material properties in materials tab. However, when i go to cell zone condition, i can only put one value for boussinesq...

04 November 2020 3,943 3 View

How can I assess purity via HRMS? What is the acceptable deviation from the calculated mass?

28 October 2020 813 3 View

Why red colour pomegranate variety are quickly degrading as compared to green colour Fruit.?

Pomengranate, Fruit wall, degradation

12 October 2020 6,431 13 View

Can you Help me with NextNano software?

I need to understand the basics of NextNano. Can anyone provide me with helping materials. Paper, thesis or book. Any set of basic simulation would also be helpfull.

04 October 2020 1,621 3 View

How can I calculate yield of product and conversion from GCMS without using internal standard ?

I am doing a synthesis of solketal from glycerol and acetone. I want to know about the conversion of glycerol and yield of solketal by using GC-MS. Is it possible to calculate the conversion...

24 September 2020 8,913 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View