I need to do micro-edm machining process. Where i can do it. kindly tell the availability of micro edm machining in any engineering colleges?
Dear Senthilkumar Ts;
Greeting, you know one of important problem in micro EDM is the fabrication of micro tool (cathode) to achieve cutting so you can do it if you have WEDM machine to fabricate tool first , then use EDM .
Hi, You can approach at IIT Mumbai, SVNIT, Surat, IIT, Kharagpur. ALl are having tMicro EDM facility.
Regards
IIT Mumbai, SVNIT surat , IIT Kharagpur
Janak Valaki (PhD) Sir, thanks for your response.
Hi! Micro EDM facility is available at NIT Calicut - advance manufacturing centre. You can visit the website for more details
Thanks for your response
First of all, it would be important to know what application in Micro-EDM is to be fulfilled.
Hi all. Is it possible to correlate multiple parameters like fruit weight, color, length and diameter, its ratio with water content in coconut ?. Need some guidance on some non destructive methods...
23 July 2024 9,421 3 View
I am designing a patch antenna using coax feed in HFSS. I read in posts that dimensions of radiation box should be more than lambda/4 from the edges of the radiating structure. So I did like that...
17 January 2023 9,053 7 View
I am designing a patch antenna with coax feed for 3GHz frequency. While assigning radiation box the height of the box needed to be assigned I found it should be above lambda/4 which was around...
06 January 2023 541 4 View
My professor asked me to replace normal ground plane with infinite ground palne and compare between them for a patch antenna. I don't know how to add a infinite ground plane in CST can somebody...
21 December 2022 6,840 3 View
I am working on the electrolytic oxidation of 5-hydroxymethylfurfural. I am currently storing 5-hmf dissolved in water in the refrigerator, but I am not getting good experimental results, perhaps...
04 December 2022 6,080 1 View
I am university student and study HMF(5-hydroxymethyl furfural) electrooxidation. I use HPLC analysis and UV-vis ,but I don't know it well. I use ion exclusion mode column. I am researching...
27 October 2022 6,133 3 View
Actually I have PDMS, it clear and highly viscous in nature, so what can I mix with it to mould them to sheets of 0.5mm thickness. Please also let me know the method that I can use for curing.
10 May 2022 9,600 3 View
Geopolymer concrete research by using Na2sio3 or k2sio3 powder
01 January 2022 6,330 3 View
I designed a antenna working at MHz range. I got -10 db impedance bandwidth for certain range of frequencies. In that range of frequencies I got a spike in impedance bandwidth for -2db. I tried...
25 October 2021 8,732 4 View
Hello fellow researchers! I am trying to find a fluorocarbon oil that has a refractive index same as or greater than that of water (1.33). The closest one I can find so far is 1.3 (FC-170).
02 May 2021 561 1 View
I am trying to replicate results published in the journal paper published recently (Modeling of Laser-assisted micro-milling Inconel718 ). In that paper, they used vdflux subroutine to obtain...
05 July 2024 3,701 0 View
Sir, I want to work on the laser assisted machining (turning) of Nickel Based Super alloy. Please help in finding the laser assisted machining facility in India. Thanks and regards
02 July 2024 2,086 2 View
Hello everyone, I need assistance to remove the oxide formed on the Ti6Al4V. During the cutting by wire EDM, oxide was formed on the surface of the alloy. Since the micron level features are...
22 May 2024 5,871 4 View
Please some examples for WASPAS,CRITIC ,COPRAS in optimizing machining parameters!
01 May 2024 6,614 0 View
I am currently trying to get a Skyscan 1072 micro CT to work again. After the mainboard on the original PC died, we tried to set the machine up on a new computer. We managed to control the source,...
28 April 2024 381 0 View
OPTIMIZATION
28 April 2024 9,186 1 View
I have done micro milling and these dark spots are visible in both conventional micro milling and ultrasonic vibration assisted micro milling. What can be these possible spots on the machined...
20 April 2024 6,644 0 View
Regarding WASPAS,CRITIC and COPRAS
17 April 2024 2,959 0 View
Regarding CRITIC,WASPAS etc...
17 April 2024 3,070 0 View
How the adhesion of thick SU8 to copper seed layer can be improved ? And which SU8 resist would you recommend for MEMS ? Thank you.
05 March 2024 5,029 1 View