Sir,
I want to work on the laser assisted machining (turning) of Nickel Based Super alloy. Please help in finding the laser assisted machining facility in India.
Thanks and regards
Check in ARCI, Hyderabad. They have this facility
https://dst.gov.in/innovative-laser-assisted-machining-technique-promises-cost-reduction-and-precision-manufacturing
Thank you for the information sir
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,800 2 View
I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...
31 July 2024 2,030 1 View
we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]
29 July 2024 6,626 0 View
Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.
25 July 2024 7,497 2 View
In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....
24 July 2024 8,075 3 View
Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?
21 July 2024 7,545 0 View
I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.
18 July 2024 4,216 0 View
I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.
17 July 2024 5,633 4 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
im studing gaussian 16 with reading paper about I-131 Metaiodobenzylguanidine in the paper "In a similar vein, nuclear magnetic resonance shielding values were investigated using the widely...
16 July 2024 6,037 4 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,175 1 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,893 2 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,289 1 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,167 2 View
Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...
23 July 2024 6,124 1 View
What is the harnessing rainwater harvesting for climate change adaptation and how is India trying to ensure rainwater harvesting?
20 July 2024 6,039 2 View
I would like to use biofilmQ to analyse confocal laser image, how can do?
16 July 2024 7,626 2 View
What was the impact of the reform movement on India and impact of land reforms on small and marginal farmers?
09 July 2024 9,780 0 View
Hello ! I would like to do band structure calculations of perovsikites materials with quantum espresso. For this I installed the Intel Fortran compiler. This is what I get when I run the...
08 July 2024 1,206 0 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,180 8 View