02 December 2017 1 10K Report

I am leaving this title for an open discussion. Can any one please suggest me the machining parameters that must be considered for both, the machining process and the ultrasonic vibration setup in spindle/workpiece ?

More Chandrakant Kumar Nirala's questions See All
How to measure FWHM from XRD analysis?

From XRD analysis how to measure Full Width Half Maxima (FWHM)?

15 September 2019 4,589 5 View

How to explore crystal structure of unknown material from XRD pattern, not listed in any of database like COD, ICDD, JCPDS, etc.?

Recently, We have synthesized a material having structure A2BO4, the XRD pattern of synthesized powder doesn't match with any reported XRD pattern or theorectical databases.

16 April 2018 2,791 3 View

In absence of balancing grooves, will the valve make a grunt noise?

We are facing the problem of grunt noises in our steering systems. Please advise whether we should increase the number of balancing grooves on the spool.

01 November 2015 6,516 2 View

What are the sources of intrusion data for wireless sensor networks?

Intrusion data for infrastructure networks are available. Can any body help in finding the datasets for intrusion detection in wireless sensor networks?

09 October 2014 6,713 5 View

What software is available for the analysis of qualitative data in social science research?

It becomes very difficult to analyse qualitative data. Quantitative data takes a lot less time to get results.

16 December 2012 2,597 37 View

Similar questions and discussions
Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

Small displacement measurement in vacuum?

Hello, I have a question. there is a circular thin foil which vibrates in vacuum, the foil restricted and moves up and down. it is like a diaphragm between two pipes . both sides are in vacuum but...

18 February 2021 8,075 3 View

How could I do a simulation for the energy consumption of a CNC machine?

I'm working on my dissertation and it is about how to save energy when a CNC machine goes to idle mode. (A concept model of the idle machine energy saving in industrial manufacturing...

26 January 2021 9,620 5 View

Please I need MATLAB code for dynamic vibration analysis of piezoFGM plate finite element modeling?

Dear all I need some help; I am working on dynamic vibration analysis of FGM plate with piezoelectric patch using finite element modeling using MATLAB using finite element modeling

23 January 2021 3,946 3 View

Forced Vibration Testing using FDD?

Hi, Can we use FDD algorithm for forced vibration response (sinusoidal response produced from eccentric mass vibrator)? Thanks

22 January 2021 5,851 2 View

Is it possible basic matrix material having higher material removal it's corresponding composites materials In wire EDM process ?

Actually, I am working with Al-B4C- Al2O3 hybrid composites. I have performed the operation by utilizing the wire EDM process to my developed composites. I found alloy 6061 as a base matrix having...

21 January 2021 7,381 3 View

Simulation of Reinforced foam core sandwich composite panel in ABAQUS. How to add the reinforcements in the sandwich panel? Any available resource?

Hello everyone! First, I would like to thank you for taking time to help me out. I am a final year student, studying Aeronautical Engineering and for a project, I need to do an analysis of...

15 January 2021 7,888 3 View

Can we control the position and vibration, simultaneously, of a flexible link with a tip mass using only the actuator's input?

This is a boundary control problem of a hybrid ODE-PDE system. The system consists of an actuator, a flexible link fixed to the actuator, and a tip mass at the free end of the link. In most...

13 January 2021 8,050 2 View

Micro CT of fiber reinforced composite - phase identification?

Hi, I have a fiber reinforced polymer matrix composite and I am analyzing it by micro CT but I am unable to reconstruct the fiber phase of the composite. how can I find a solution for this?...

07 January 2021 5,680 1 View

How to Simulate Ambient Vibration to input into Numerical Model?

Hi All I want to simulate an ambient vibration to be used as an input to a Numerical Model. I want this to represent the vibrations occurred to the building through the wind, vehicle/human...

05 January 2021 9,228 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close