What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

Has anyone succeeded in capturing uranium atoms in a fullerene structure?

Additional questions are: What are the encapsulating atoms? How difficult was the process and what rates were achieved? What factors most seriously affect the economics?

20 February 2021 3,134 5 View

How to phrase semi-structured interview questions using IPA without biasing superordinate themes?

Hello, I am preparing a semi-structured interview schedule for an interpretative phenomenological analysis study on marginalized individuals' career experiences as impacted by COVID-19. The aim...

19 February 2021 9,099 2 View

No title

19 January 2021 6,848 4 View

Why do my fibroblasts under hypoxia conditions proliferate slower than the same fibroblasts under normoxic conditions?

I am using healthy control lung fibroblasts in a 96 hour experiment with two drugs (nintedanib and Pirfenidone) and vehicle controls for both. I have both hypoxia (approx 1% O2) and normoxia...

12 January 2021 6,260 1 View

How much does radiative heat transfer effect thermal conductivity of materials and how to compare calculations to experirment?

I am calculating the phonon contribution to thermal conductivity for 4 perovskites (BaZrO3, BaSnO3, BaHfO3, and KTaO3) with relatively wide bandgap. When I compare my results for BaZrO3 to the...

27 December 2020 3,232 3 View

Proper method for assessing model invariance following Confirmatory Factor Analysis (CFA) and preceding 2x2 between-subject analysis?

I have produced a good-fitting, reliable baseline model according to CFA. The model contains several factors each loaded by several categorical (ordinal) items. I ultimately intend to analyze the...

15 December 2020 1,668 4 View

How to Reinstall Operating System for a TA Instruments 2910 DSC?

Hard drive crashed on an old windows 2000 that was used to control a TA Instruments 2910 DSC. Installed new hard drive and I am trying to figure out where I can find the software/operating system...

17 November 2020 2,467 3 View

Communities based websites do they serve a purpose?

I'm asking and posing this question as it forms a part of my final project year. I building an ASP.net community-based website coupled with an Oracle database and I'm looking for feedback,...

17 November 2020 7,852 1 View

How can I solve Error: "The coupling service failed to start" during simulation ANSYS 2Way FSI?

Hello, I am dealing with error during lounching 2 Way FSI in ANSYS Workbench. Setup of the Fluent is ok (stand alone I am receiving expected results) and FEM uses Transient Structural. Once I run...

11 November 2020 3,816 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View