Stir casting setup for composite material
What experiments you want to conduct?
Important tips for writing a good review articles
24 February 2021 8,544 6 View
Hi, I'm trying to analyze a Kratky plot generated from my SAXS data. I am seeing multiple bell-shaped curves in my Kratky plot and I am not able to find any source to get relevant info on this...
20 January 2021 2,474 1 View
Hi, I'm doing 5/40nm In/Au e-beam evaporation at rates 0.2A/s(for In),1A/s(Au) on lithographically(doubly coated 495k,950k PMMA e-beam resist) done Si substrate at base pressure 2e-6torr. I'm...
18 January 2021 7,550 4 View
I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.
17 January 2021 5,450 3 View
a PCR and gel electrophoresis was carried out to obtain the results. they are negative jak2 v617f samples (ref genome - NG_009904 )
13 January 2021 7,658 4 View
Since Abaqus CFD is no longer available in newer versions what are other available codes for Fluid-Structure Interaction Simulation
11 January 2021 2,012 3 View
I want to mark the neurons I am recording from during whole cell Patch clamp. I am thinking of using Lucifer Yellow. Does it increase noise during recording? What are the better alternatives to...
04 January 2021 7,791 3 View
I would like to know application of learning and control in MAS setting. And where could I find simulation codes of learning in MAS control
04 January 2021 1,866 4 View
I am studying about Impact load resistance property of Polyurea (Elastomer). With respect to this, I need to conduct tests on this material to evaluate its material model behavior as a...
29 December 2020 2,969 1 View
This is required since the stress v/s crack length has to be determined
23 December 2020 3,446 1 View
For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys
23 February 2021 8,839 3 View
I have been trying to synthesize PVDF thin film by solvent casting method. I started by using 2:3 DMSO: acetone as solvents. The solution was stirred for 3hrs at 60 deg and was dried at 90 degrees...
09 February 2021 8,850 3 View
A huge amount of water is evaporated to cool down and solidify the liquid metal strands coming out of bottom of CCM mould. The steam contains significant latent and sensible heat energy, besides...
26 January 2021 3,446 4 View
Super austenitic stainless steel castings showed liquation crack after liquid penetrant testing post heat treatment. How to reduce this in thick walled castings.
26 December 2020 7,959 3 View
Want to know the relation between sdas and solidification rate, the mechanism by which getting smaller space between secondary arms by increasing the rate ?
23 December 2020 735 2 View
Hello everybody, I am looking for information about precipitation hardening/ageing of die casting alloys identical with or related to ANSI/SAE 385.0 - according to specification, this alloys...
30 November 2020 1,701 3 View
I have conducted research on characterisation of Al7050 + B4C by electromagnetic stir casting. The alloy employed in the process is casted alloy and the Composite too is casted. How much strength...
16 November 2020 9,226 3 View
I have been asked this question so many times. I give a general answer based on a metallurgy book which states that 'wrought iron can not be cast'. However, you can cast wrought aluminum alloy...
12 November 2020 5,163 9 View
The Cu5MCuC Inconel casting produced by pouring into a sand mold seems to have developed several hot tears/hot cracks. The cracks opened up after heat treatment. How the tears/cracks could be...
01 November 2020 190 5 View
I would like to prepare a thin film from of PDMS liquid. My current attempts with solvent casting, then let it dry for 24 hr at room temp. after I tried to recuperate and it doesn't work. Any...
08 October 2020 8,745 4 View
