Looking for PDMS sheet manufacturers

Niraj Jadhav @Niraj-Jadhav

01 January 1970 0 4K Report

Hi all,

I am looking for manufacturers of customized PDMS (Polydimethylsiloxane) sheets (membrane/film/layer/roll).

If you have any contacts then please share. It'd be really helpful.

Thanks in advance.

Kind regards,

Niraj

Badges
Science topic

More Niraj Jadhav's questions See All

Given, ER = 0.2, WHAT WILL BE THE AIR FLOW RATE IN kg/hr?

I have a biomass with given ultimate and proximate analysis data. I am using Aspen plus for the simulation of gasification of biomass. In experimental data the gasifying agent air flow rate is...

18 June 2024 2,743 1 View

Can anybody guide me for How to solve polynomial equation for checkpoint analysis in formulation development"?

I have done formulation development of tablet for which i have considered two independent variable. Results are plotted in a statistical analysis software and polynomial equations are generated....

24 April 2024 3,951 1 View

Why plant taxonomist only follow APG system of classification. Why countries like India don't have their region based classification system ?

Ancient India believed in traditional system of schooling called Gurukul, however sociopolitical developments and modernization of culture gradually wiped away the tradition. This eventually...

20 April 2024 9,414 0 View

How can i solve this error in ASPEN PLUS?

i am doing a project on gasification. during pyrolysis i got the following error: * WARNING COMPONENT 'BIOMASS' IN SUBSTREAM 'NC' HAS ZERO FLOWRATE IN THE OUTLET STREAM. FRACTIONAL...

18 March 2024 6,025 1 View

How to derivatize Amino Acids using N-tert-butyldimethylsilyl- N-methyltrifluoroacetamide (MTBSTFA) for GC-MS analysis?

I recently attempted to replicate the amino acid derivatization procedure outlined by Sobolevsky et al. 2003. While I followed the steps diligently, unfortunately, I did not achieve the expected...

28 February 2024 7,101 6 View

How can i solve this error in ASPEN PLUS: COMPONENT 'DRY-BIOM' IN SUBSTREAM 'NC' HAS ZERO FLOWRATE IN THE OUTLET STREAM. FRACTIONAL CONVERSION ?

Dear all, I am doing a gasification of biomass. In the pyrolysis section i have used RSTOIC for the devolatization of the biomass. i have specified the yield from the RSTOIC. it gave me the...

19 February 2024 8,026 0 View

Do electrons really revolve in orbits in atoms?

https://youtu.be/etausaYnFqQ?si=hxtrW321C5N8JtTT

14 January 2024 3,914 0 View

How to avoid Pin holes and micro porosity issue in thermal Spray and Induction Fused coaitng?

•Coating method- Thermal Spray and Induction Fused. (Thermal coating by metco 6P-2 torch and fusing by induction heater.) •Part material- AISI 1035 Steel Plunger (4.5'' Dia.) coated by Water...

06 November 2023 7,445 1 View

Has it really been verified experimentally that there is no phase difference between electric and magnetic fields in an electromagnetic wave?

In an electromagnetic wave, the energy of the electric field is converted into a magnetic field and vice versa. So there should be a 90 degree phase difference between them. Not only this, as the...

26 July 2023 9,417 5 View

Welding Simulation using ABAQUS for dissimilar materials?

Hello everyone, currently m working on welding simulation of dissimilar materials in ABAQUS software. i have modeled two different plates separate for dissimilar materials. After simulating the...

01 July 2023 1,513 3 View

Why PDMS is not hardening ?

I use PDMS to build a microfluidic system, but it is not hardening at all, although I use TEOS as a cross-linker and also ATPES in a ratio of 1:10, and it's been 3 days at 80 degrees of 3 ml cast...

01 July 2024 604 3 View

Chemical composition of curing agent for PDMS (Sylgard 184 Kit) and solid percentage?

1- Please provide information about the chemical composition of curing agent for PDMS(Sylgard 184 Kit)? 2- what dry solid percentage is obtained for a ratio of 10 to 1(PDMS to hardener)?

30 June 2024 6,814 2 View

Cut PDMS sheet with Graphtec cutter plotter CE6000-40?

Dear All, I want to cut PDMS sheet with thickness of 0.8 mm to rectangular shape with Graphtec cutter plotter CE6000-40. What condition do you offer? Do you offer any kind of special speed or force?

25 June 2024 8,111 1 View

How to reduce the permeability of pdms?

I want to trap fluid (water..) in the PDMS channel for a long time. After a short period, the channels become empty of fluid. Is there a way to reduce the permeability of PDMS?

17 June 2024 2,703 4 View

How to color PDMS?

Hi, I am trying to color a very thin (3um), spincoated layer of PDMS with a dye (I want to make the thin layer visible to the naked eye). Does anyone have experience with dyes/ colors and...

11 June 2024 7,330 2 View

What is name of this chemical reaction process?

My research object is changing terminal functional group of PDMS from -OH to -PO(OH)2. I know just one experiment recipe using furan, ethylamine, POCl3, D.I water. But it not work well. So i want...

09 June 2024 5,290 0 View

Why is my thin film PDMS TFM device warping only when with cells?

I've been fabricating traction force microscopy devices in glass bottom dishes, using a method that first spins a 100 micron PDMS layer, then a ~1 micron PDMS + fluorescent beads mixture layer....

09 June 2024 652 2 View

Is bonding PDMS to PI (Kapton) using a plasma treatment possible?

I’m looking into bonding a PDMS microfluidic circuit to a PI sheet using a plasma activation method. The PDMS will be on the order of ~700 um thickness, while the PI will be 12.5-50 um. I have...

24 May 2024 7,050 1 View

Is there a way to use Trichloro(1H,1H,2H,2H-perfluorooctyl)silane without using vacuum chamber?

I've been wanting to use 3D printed mold (resin) for curing PDMS for micro-contact printing. I figured that PDMS wouldn't come off that easily so silanization would be required however, I do not...

22 May 2024 4,809 1 View

Is there any flexible polymers similar to PDMS, but has hydrophilic property?

looking for a polymer which, 1) will be used for microchannel (cross-section: rectangle with 1.4-1.6 mm width, linear configuration) fabrication 2) easy to fabricate similar to PDMS 3) Permanently...

08 May 2024 6,472 1 View