20 February 2024 0 8K Report

Dear all,

I am doing a gasification of biomass. In the pyrolysis section i have used RSTOIC for the devolatization of the biomass. i have specified the yield from the RSTOIC. it gave me the following error while simulating. Any HELP?

More Niraj Neupane's questions See All
Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Similar questions and discussions
Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

How can I add own Henry coefficients in Aspen Plus?

Hi, i would like to simulate an absorption process in Aspen Plus. I want to use the NRTL model und would like to add some individual Henry coefficients. Is that possible and how?

05 August 2024 2,333 2 View

VOC analysis on GCMS ?

Hi everyone, Can someone explain for me a method to inject VOC collected with Tedlar bag from pyrolysis process and transfer or inject into GCMS. Thanks

22 July 2024 6,398 1 View

How calculate the conversion alph from tga analysis?

I read it Convert the y-axis from mass loss to degree of conversion (100-x)%. What if tga analysis have residual char, for example at mass loss% 27% Is it the same eqation to get conversion...

15 July 2024 4,218 1 View

Where is the stream gradient usually greatest and relationship between the slope of the stream channel and the velocity of the stream?

Where is the stream gradient usually greatest and relationship between the slope of the stream channel and the velocity of the stream?

13 July 2024 5,825 0 View

Where river velocity the greatest and relationship between average stream velocities is, stream roughness, and stream gradient?

Where river velocity the greatest and relationship between average stream velocities is, stream roughness, and stream gradient?

13 July 2024 3,199 2 View

What happens to stream's discharge if gradient of a stream increases & relationship between gradient of a stream & rate of water flow?

What happens to the stream's discharge if the gradient of a stream increases and relationship between the gradient of a stream and the rate of water flow?

13 July 2024 5,085 2 View

How does that stream's gradient change downstream as it enter the alluvial fan and difference between an alluvial plain and a delta plain?

How does that stream's gradient change downstream as it enter the alluvial fan and difference between an alluvial plain and a delta plain?

12 July 2024 7,337 0 View

How does stream gradient steepness change moving downstream and gradient of a stream change along its longitudinal profile?

How does stream gradient steepness change moving downstream and gradient of a stream change along its longitudinal profile?

12 July 2024 4,113 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close