How much change in hot and cold formability will be there if alloys with poor fomabilty is forged or rolled under vacuum?

Some of alloy steels and superalloys have very small forging window and one faces problem of cracking during hot forging and rolling and are preferentially isothermally forged.It could be...

27 January 2020 2,548 2 View

How we can determine critical temperatures like ac1,ac3,Ms Mf and liquidus temperature of a steel alloy by thermo mechanical simulator?

In my experimental alloy I want to calculate the actual critical temperatures of alloy steel like ac1.ac3.Bs. Bf, Ms,Mf,liquidus and solidus temperature by TMS GLEEBLE 3800.This will help me in...

15 May 2018 6,312 7 View

If warm bending of high hardness armor sheets are bended ,can some body tell how much time plates should be heated before warm bending?

Required for my project

17 January 2018 2,331 2 View

Titanium or Tantalum?

19 August 2014 170 7 View

Can we use S/N analysis for Full-factorial experiments?

We are planning to conduct full factorial experiments. I found in most of the literature that the analysis associated with Full Factorial experiments is ANOVA based on coefficients. I wan to know...

30 July 2014 7,835 4 View

Do we have to follow the sequence of experiments while performing experimentation in Taguchi methodology?

Can we perform all those experiments which are at one level and then move to the other? For example: There are three levels of cutting speed - 1000m/min; 2000m/min and 3000m/min; 1000m/min setting...

20 March 2014 4,991 3 View

How to simulate mobile agents using castalia?

Dear Researcher, I read your paper bench mark itinerary algorithm, the survey is done excellently, could you please guide me as how to use castalia for simulating mobile agents.

01 January 1970 8,905 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View