How we can determine critical temperatures like ac1,ac3,Ms Mf and liquidus temperature of a steel alloy by thermo mechanical simulator?

In my experimental alloy I want to calculate the actual critical temperatures of alloy steel like ac1.ac3.Bs. Bf, Ms,Mf,liquidus and solidus temperature by TMS GLEEBLE 3800.This will help me in...

15 May 2018 6,312 7 View

If warm bending of high hardness armor sheets are bended ,can some body tell how much time plates should be heated before warm bending?

Required for my project

17 January 2018 2,331 2 View

Titanium or Tantalum?

19 August 2014 170 7 View

Can we use S/N analysis for Full-factorial experiments?

We are planning to conduct full factorial experiments. I found in most of the literature that the analysis associated with Full Factorial experiments is ANOVA based on coefficients. I wan to know...

30 July 2014 7,835 4 View

Do we have to follow the sequence of experiments while performing experimentation in Taguchi methodology?

Can we perform all those experiments which are at one level and then move to the other? For example: There are three levels of cutting speed - 1000m/min; 2000m/min and 3000m/min; 1000m/min setting...

20 March 2014 4,991 3 View

How to simulate mobile agents using castalia?

Dear Researcher, I read your paper bench mark itinerary algorithm, the survey is done excellently, could you please guide me as how to use castalia for simulating mobile agents.

01 January 1970 8,905 4 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Small displacement measurement in vacuum?

Hello, I have a question. there is a circular thin foil which vibrates in vacuum, the foil restricted and moves up and down. it is like a diaphragm between two pipes . both sides are in vacuum but...

18 February 2021 8,075 3 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View