Line load by pressure load in abaqus?

Behrouz Zarei @Behrouz_Zarei

09 September 2015 1 3K Report

hi,i want to specify a distributed line load in abaqus by pressure load,but in pressure load we must select a surface.

is there any one who can give me a tip?

thanks.

Dinesh R. Satpute

Hi,

If I want to apply UDL or UVL in ANSYS I usually use pressure on beam option instead of pressure on line. I am not familiar with abaqus but hope this will work.

Have a nice day.

Badges
Science topic

More Behrouz Zarei's questions See All

Abaqus initial stress defininig in version 6.10?

hi there, is there any one who can tell me is initial stress in predefined load exist by own in abaqus 6.10 or we shoud define it in subroutine?

04 May 2015 1,481 0 View

How can I define material property in abaqus?

how can we define material property in abaqus? especially elastic and plastic coefficient of reinforced concrete?

04 May 2015 3,980 3 View

Reinforced conceret beam modeling with Abaqus?

is there any one who can help me to model a reinforced concrete beam with Abaqus?give me the steps from the scratch?

03 April 2015 8,507 3 View

Is it possible to install abaqus 6.1.10 on windows 8?

how can i install abaqus 6.1.10 on windows 8

01 February 2015 2,484 0 View

How to install abaqus 6.1.10 on windows 8?

is there any one who can put me on the way escaping windows checking system during the installation of abaqus 6.1.10 on windows 8?best regards.

31 December 2014 6,911 6 View

wire rope

how can we model a wire rope?

06 July 2014 8,016 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View