18 September 2020 2 2K Report

What are the journals best suited for submitting articles about semiconductor simulation device algorithms? For my specific interest, this would concern TCAD simulator algorithms, which solve PDEs on a mesh, using Finite Volume Methods.

More Juan E Sanchez's questions See All
What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How can I improve the concentration of banana fruits extracted RNA?

Currently, I'm working with banana fruits. I've tried to do RNA extractions with different methods, and I've gotten total RNA without contamination, but I couldn't get a high concentration of...

22 February 2021 6,126 2 View

HPLC baseline failure (ACN/Water)?

My baseline increases without any explanation, it is only fixed by changing the solution B, will it be the column? Reagents? Bomb? Detector? Solution A: H3PO4 0.01% IN WATER Solution B: H3PO4...

21 February 2021 5,656 3 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

How to improve the buffer capacity of sea water?

Hello everyone I would like to improve the buffer capacity of seawater (pH ~8) in order to dissolve as much CO2 as possible without dropping the pH below 7.5 (a range between 7 - 7.5 is...

17 February 2021 2,797 2 View

Where can I find a reliable and updated methodology related with the design of spiral heat exchangers?

I need to design an spiral heat exchanger, buy I don't know what reference or bibliography (preferably a book) should I consult in order to get an updated and reliable methodology related with...

14 February 2021 7,910 3 View

Resume Book UEP2013 Asian Edition, dis somebodey has it?

I am looking for a copy of the resume book of UEP2013 Asian Edition (Urban Environmental Pollution 2013 Asian Edition) held in Beijing. If somebody has it, please I would like to obtain an...

11 February 2021 2,247 2 View

Can a mRNA be degraded but still observe a protein over-expression?

Hello there, I'm currently trying to over-express a gene by transfecting the cells with a pcDNA6 plasmid containing my target gene. When I measure the mRNA for my gene of interest, the levels are...

03 February 2021 4,112 4 View

How do they fill/replace metal hydrides in vessels?

Surely they will want to avoid contact with air/moisture, so what is the procedure for this?

23 January 2021 428 2 View

Similar questions and discussions
fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to add a journal?

I would like to know how to register the journal Flora Montiberica (ISSN 1138-5952 - eISSN 1988-799X) in Research Gate.

02 March 2021 8,156 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close