Is there anybody work with Eulerian model in Nanofluid simulation in Fluent?

More Khalid B. Saleem's questions See All

Double diffusive problem within a cavity?

Dear all, I am attempting to simulate a double diffusion (Natural convection+Mass transfer) problem in a square enclosure utilizing humid air in which there is a high concentration at the left...

07 August 2019 3,675 6 View

Can surfer plor triangular contour map?

I attempted to draw contour for stream function for triangular cavity in surfer 9 I was export the data file from Fluent and build a grid file for it in surfer 9 after then I plot the contour it...

06 July 2018 5,022 2 View

How to convert stream function units in FLUENT code

As it known Fluent define the stream function as the mass rate of flow between the streamlines so it showing it in terms of (kg/s) in contours. My question how I can convert this unit into...

06 July 2017 4,582 5 View

How to get reviewers to a paper?

Hello I submitted a paper to an international journal and during registration process at the journal site they asked me to add external reviewers may somebody assist me with sending me webpage of...

04 May 2016 7,446 3 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

Ghassan Fadhil Smaisim Popular answer

Dear Khalid,

Please see the following paper:

https://www.researchgate.net/publication/319445996_Enhancement_Heat_Transfer_of_Cu-Water_Nanofluids_with_Thermophysical_Properties_Modeling_by_Artificial_Neural_Network

Good Luck

Article Enhancement Heat Transfer of Cu-Water Nanofluids with Thermo...

Ghassan Fadhil Smaisim

Mohammed saad Kamel

Dear Dr. Khalid. I recommended you to try firstly the mixture model especially if you are going to use low or intermediate loading for dispersed particles in basefluid. because the flow physics in such case (coupling between the phases is one or two way) DMP, mixture and Eulerian models will be suitable for such simulation.