Is there a way to convert or transform blood chem results of mice in the normal values for rodents?

04 February 2019 0 1K Report

we submitted our blood samples (mice blood) in a diagnostic center and they run it using the normal values for humans. is there a way to convert our results to that of rodents'?

thank you. i hope you can help.

Badges
Science topic

More Queennie Riva's questions See All

HPLC_MS or GC_MS analytical method for acrolein, without sample pretreatements?

Can anyone suggest a GC-MS or HPLC-MS analytical method to identify Acrolein in a solid sample (soluble in ethanol), without any pretreatement of the sample (no purge and trap, no SPME)?

24 March 2020 3,419 9 View

What is the standard ratio for ethanolic extraction?

I happen to use 300 g and soak it in 1L of 95% ethanol.

13 September 2018 5,592 6 View

Does anyone have any scoring systems for liver and kidney histopathological evaluation?

06 April 2018 9,753 4 View

I need a dose of 2000 mg/kg and the method I used for plant extraction is decoction. How can I calculate the concentration of the extract?

I am having trouble preparing an extract and calculating the required dosage and concentration of the extract. When using decoction as my extraction method, do I need to use rotary evaporator or...

16 March 2018 7,450 5 View

Which is a good anti-somatostatin antibody for IHC?

I am looking for a good anti-somatostatin antibody for fluorescent immunostaining of mouse interneurons

22 October 2017 4,338 3 View

Isolation of single cell from human lung tumour tissue?

Hi, I am planning to isolate single cells from human lung tumour tissue. I am wondering what is the best way to enzymatically degrade the tissue to isolate MOST of the cells (since the population...

09 April 2017 3,212 1 View

How can I quantify tumor burden in mouse lungs in a metastatic model of Lewis lung carcinoma?

I am setting up an experimental metastatic model of Lewis lung carcinoma by intravenous injection of LL/2 cells into the tail vein. I am looking for ways to quantify tumor burden in the lungs. I...

27 February 2017 8,094 2 View

Rocking curve scan XRD ?

1) can you scan rocking curve in a normal 2theta-theta diffractometer (Bragg brentano) bruker D5000? 2) which slides use? 3) what is the difference between FWMH obtained through a normal scan and...

24 July 2016 3,044 1 View

Is there any data - different by the one Eich - exploring the mechanisms involved in remembering events in first (field) or third (observer) person?

To my knowledge the most relevant references are the ones by Eich: Eich, E., Handy, T. C., Holmes, E. A., Lerner, J., and Mcisaac, H. K. (2012). “Field and observer perspectives in...

01 March 2016 2,763 2 View

Is the lung tumour in Lewis Lung Carcinoma model (formed upon subcutaneous injection) a primary tumour?

Apart from the subcutaneous tumour, is the lung tumour also primary or metastatic? If metastatic, does it still represent actual lung tumour?

02 February 2016 535 3 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View