Is the Crimson publisher is reliable to publish our research outlets?

More Zhwan Sktani's questions See All

Change vol.% & mol. % of ZrO2 to wt. %?

Dear Colleagues, We have found several manuscripts compare the effect of ZrO2 on the physical, microstructure and mechanical properties of ZTA, using various amount of ZTA. few researchers use...

19 April 2020 5,737 20 View

References (Book or other materials) for Teaching (Research Methodology) course at postgraduate students level?

Dear Colleagues, Thank you for your usual cooperation. Kindly, could you advise me the best REFERENCES for teaching (RESEARCH METHODOLOGY) course to master students? Any assistance through...

14 December 2019 8,718 10 View

How to shift (2 theta) of an XRD pattern in Highscore X'Pert?

Dear Colleagues, I humbly request for an urgent support. I have many ZTA compositions added with different oxides. However, when I insert them into Highscore X'Pert software, it is obvious that...

23 October 2019 8,903 3 View

MATlab vs ANSYS for Imagae analysis for FESEM?

Dears, I have a planned idea to govern a software for image processing , simulation and (maybe) coding or decoding of mechanical properties analysis through an appropriate software. 1- you...

24 September 2019 9,392 5 View

KIC vs KIFR (Fracture toughness)?

It is well known that KIC is a measure of materials property (intrinsic) is called a fracture toughness, while the KIFR according to ISO 14627 (2012) is defined as a resistance to cracking as...

04 November 2018 8,345 13 View

What is the difference and relationship between flexural strength and bending strength in ceramics?

Dear Colleagues, The term of bending strength and flexural strength are interchangeably used to measure the strength of ceramic materials. I am aware about the bending...

01 January 1970 1,311 18 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to upload pdf of my articles published?

03 March 2021 2,183 3 View

Would adding books published in Lambert Publishers increase my RG impact?

There are some books published in LAP. Shall I add it to the RG?

02 March 2021 2,753 1 View

What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is Journal of Agricultural Research a predator?

it is published by Juniper

28 February 2021 354 4 View

How can I publish a manuscript in free or low cost journal with good H-Index?

Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...

28 February 2021 7,800 6 View

Which software is better to write systematic review paper?

We have seen some authors use some software to write review paper. As obvious, the study of all published papers concerning our studying field is not possible and these software can help us to...

27 February 2021 6,296 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

Which index or sites are reliable in determining of plant species?

There are many indexes when determining plant species: Plants of the World Online (POWO), International Plants Names Index (www.ipni.org), The Plant List (www.theplantlist.org) and others. But...

26 February 2021 3,404 10 View

Can anyone please help me in processing SAR SLC data to generate interferogram using SNAP?

I have two scenes of the study area, one top and the other bottom. As per the tutorials and papers published, the step include coregistering the master sand slave images. However, when i try to...

24 February 2021 6,372 1 View

Zhwan Sktani

Thank you dear Biyick Paul Patrice for your answer. I got some answers in other forum, I may share it with you

https://www.researchgate.net/post/Is_the_Crimson_publisher_is_reliable_to_publish_our_research_outlets2

Miguel Coussirat

I think, but I'm not sure, that if you pay you will see your publication. I had a similar experience with other open journal. Commonly a journal take several months to perform the review. In the aforemtioned case in one week they notify me that my paper was ready (if I pay...), therefore, I didn't send the paper. The initial idea for open journal was very nice, science for everyone, but today I don't know if this initial idea survive... On the other hand, check this (and others journals) by using scopus or scholar, maybe you could obtain more information, related with these problably fake ISI journals as Rob and José suggested.