Does Barrier Layer play any role in the variability of Deep Chlorophyll Maximum?

What role does Barrier Layer play in the variability of Deep Chlorophyll Maximum (DCM) or subsurface chlorophyll maximum. Are there any papers describing this relation?

28 August 2019 6,150 2 View

How to assess the societal impact of a published paper either directly or indirectly?

Apart from the impact factor and citations to a paper is there any way to know the impact the published paper made on the society. Like the research impact metrics, are there any societal impact...

24 July 2018 2,835 2 View

CNT coating on copper using dip coating?

I need to disperse the CNT nanoparticles available with me and make a solution which can be easily dip coated on a copper surface. Anybody having experience in this?

30 May 2018 3,276 3 View

Can any suggest good introductory material to learn phython for ocean applications?

The capability of phython to solve problems is increasing day by day and hence wish to get a basic introduction to the language, specifically to solve oceanography problems.

27 December 2017 4,747 15 View

In the mode analysis by using COMSOL multiphysics, is there a way to optimize the mesh size?

I use physics controlled mesh option of COMSOL 5. But sometimes it takes a long time. When I increase the size of mesh, the circular shape of holes of PCF is apparently deformed. Could you please...

18 October 2017 1,210 3 View

How can we measure the receptivity of stigma of a flower. Is there any chemical test for this?

I am working on Fenugreek (legume).

24 January 2017 262 4 View

Is there any tool other than QMOOD++ to measure the metrics stated by BANSIYA(QMOOD metrics) for a class diagram?

Is there any tool other than QMOOD++ to measure the metrics stated by BANSIYA(QMOOD metrics) for class diagram?

22 June 2016 4,064 5 View

Where can I get chemical kinetics and isotherm methods, software and templates?

28 November 2014 466 8 View

To improve the simulation time.

I am working with parameter sweep with COMSOL. when the simulation is functioned several times. I feel the time taken to simulate is increasing that the past. can you help me to solve this?

01 January 1970 5,483 6 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View