Is it possible to define freeform faces in Abaqus 6.14?

22 November 2017 1 6K Report

Hi! Is it possible to define freeform faces in Abaqus 6.14? I want to conntect some points to a crack surface. The problem is that the points don't lie on the same plane but the most features to partition only work for one.

Lijuan Xiong

I haven't used this software, but I think if you can create a curved surface

Badges
Science topic

More Benedikt Benteler's questions See All

How to correctly apply statistical analysis of Time Series Data?

Dear all, I have trouble finding a correct methodology to investigate if two time series are significantly different. The data is e.g. two time series vectors with 1000 samples each. The standard...

03 June 2024 5,727 4 View

Closed Abaqus model duing Topology Optimization, now it won't open?

Currently I am optimizing a part in abaqus 2020 (6.20). I unintentionally closed the software while an optimization was running. Now the whole model won't open. In the .rpy it says: # -*-...

23 September 2021 10,006 2 View

Best inducible mammalian expression system for shRNA-mediated knockdown?

Dear all, I´m planing to transduce white pre-adipocytes with a lentiviral constructs for inducible shRNA-mediated knockdown of certain target genes. Since my target genes are strongly involved in...

08 February 2021 9,265 4 View

GLMM in SPSS?

Dear colleagues, we are conducting an observational, longitudinal study with 10 groups that were tested for four times over three years with a metric outcome parameter. The last test’s will be...

30 November 2020 3,084 4 View

Indicated hydrogens in heterocyclic compounds - nomenclature?

Hello, I have a question to the IUPAC nomenclature of heterocyclic compounds. Usually hydrogen atoms in the ring system not attached to atoms connected by double bonds are denoted as indicated...

03 November 2020 3,487 3 View

Is there a good text/book on trend analyses?

Dear friends, I am looking for a book/text on trend studies and their statistical analysis. So far I found out that a trend study focuses on the same population with different individuals at...

22 August 2020 9,210 3 View

What is the best wearable EEG recording device for research?

Hi there, I am searching a wearable EEG device with as many channels and the highest accuracy possible. I found some papers which reviewed/used the following devices, but still not sure which is...

19 May 2020 6,068 2 View

What is the equivalent of pressure for a 2D sheet?

If we imagine a sheet, any essentially 2D object, we have an intuitive word to convey that the sheet wants to contract: "tension". For example, when we stretch out a bedsheet, we place the sheet...

04 May 2020 6,272 0 View

Is it possible to precisely evaluate a thickness of a NiP-Cr coating on a stailness steel with XRF?

Hello everybody, I have a qestion about the implementation of the XRF to determine the thickness of the NiP -Cr coating on a stainless steel (1.4305). According to the TDS of the base Material,...

24 February 2020 5,735 2 View

HPLC standard (mixture) for performance qualification test?

Has anyone experience in standards or standard mixtures for HPLC with UV detection for performing performance qualification tests? I am searching for e.g. a mixture of 2-3 compounds that is...

12 January 2020 714 4 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

What does the difference \lambda_j - \lambda_{j+1} represent in relation to the conjugate partition of \lambda?

For a partition of an integer \lambda, what does the difference \lambda_j - \lambda_{j+1} represent in relation to the conjugate partition, , with \lambda_j being the j-th element of \lambda?

23 July 2024 8,008 1 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View