01 January 1970 3 9K Report

I am working on concentrated to model ball bearing therefore I need to simulate it using Fluent CFD. I need to help me to create, mesh and setup this journal bearing please how I can to do this using ANSYS?

More Ahmed Ramadhan Al-Obaidi's questions See All
Can anyone provide me geometry of an axial pump with induced with mesh and setup using CFD fluent?

I am working to simulate axial pump with inducer using CFD fluent and I need help to known how can create axial pump that mean how can rotate impeller with fixed the pipe wall under transient...

01 February 2020 8,827 3 View

Does anyone teach a course on desertification?

Dear researchers I am going to teach a course on desertification but i need a help and somebody to share with me his/her experiences on teaching such a course. I would like to learn some teaching...

31 December 2019 2,384 4 View

I want to simulate journal bearing using Fluent CFD?

I am working on concentrated to model journal bearing therefore I need to simulate it using Fluent CFD. I need to help me to create, mesh and setup this journal bearing please how I can to do this...

11 December 2019 7,564 2 View

A request for an online course in principles of drug-protein and protein-protein molecular dynamic simulations?

Dear All, I am looking for an online course or website teaching the principles of molecular dynamic simulations. In specific, generating protein-protein and/or small drug-protein docking models...

10 November 2019 8,258 3 View

Is there a quantitative measurement of pH in cell culture using Phenol Red spectrophotometry?

Hello! I'm trying to determine the pH of a cell culture plate using phenol red present in the medium (MEM) and a plate reader. However, phenol red's absorbance changes depending on the pH. Is...

05 June 2019 7,514 2 View

Is there a website to obtain a Geological Map of Saudi Arabia (as shapefile)?

I am looking for a map in the resolution of Geological Formations, not according to the age of deposits in the format of shapefile or good resolution image. Thank you in advance.

01 February 2019 2,419 1 View

I want to know how nanomaterials can be used to get rid of oil contaminants?

I need accurate details for the purpose of conducting some technical tests that concern some of the problems facing the research

10 November 2018 1,315 4 View

What is the most suitable high thermal capacity materials for concrete?

I am looking for material with high thermal capacity, which is cheap and could be used in concrete and blocks?

10 November 2018 1,726 3 View

How we can know that the column used in HPLC has a good efficiency through the shape of peaks in chromatogram?

I need to know if my column which i used in the analysis with high efficiency or no.

10 November 2018 9,014 0 View

Two-Phase Flow?

Can any body tell me how to start simulation of water nucleation using COMSOL Multiphysics?

09 October 2018 5,901 5 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close