I want to draw rectangular patterns on along the circumfernce of the cylinder in fluent geomentry? can anyone help me regarding to this?

More Usama Tahir's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Conjugation of PEG-Amine to an Amino Acid Using EDC?

I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...

31 July 2024 2,033 1 View

How to get article and literature review templates (for publishing) from websites like Elsevier?

Hello, I want to know how to get the templates from the Elsevier official website (their last updated if exists)? I would like to know the steps if possible.

26 July 2024 3,264 2 View

Does soybean seed coat or cotyledon contain chlorophyl or flavonoids? What types? determined by paper chromatography? other methods (high school lab)?

Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.

25 July 2024 7,498 2 View

Does post-translational protein modification cause devisions on observed pI verses calculated pI?

In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....

24 July 2024 8,076 3 View

How I can add anew research in my account ?

Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?

21 July 2024 7,545 0 View

Can Document Analysis be used as the only method of research?

I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.

18 July 2024 4,218 0 View

How much sample we are required to do a pilot study for standardized an Achievement Test?

I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.

17 July 2024 5,633 4 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What is wrong with my input file?

im studing gaussian 16 with reading paper about I-131 Metaiodobenzylguanidine in the paper "In a similar vein, nuclear magnetic resonance shielding values were investigated using the widely...

16 July 2024 6,040 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to draw the five chelate rings of [Co(EDTA)]- on this picture?

Is this circle one of the rings?

03 August 2024 5,988 0 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

How to draw photon-magnon coupling color plot in origin?

Please help me in plotting the photon-magnon coupling plot as shown below

14 July 2024 1,632 1 View

Osama Al-Habahbeh

I advice to find a similar tutorial as the problem will depend on how the patterns are aligned with respect to the flow direction.

Usama Tahir

actually i try to find similar tutorial but i can not find the similar tutorial. different tutorial make complex geometries in solidworks then import it into ansys. could you please tell me the best tutorial similar to above patterns?