I need it for plant Design
You can get the data from ASPEN PLUS properties section and data banks, or estimate the missing parts in the molecular modeling section.
In each case check the results from independent methods or published data, because the simulator is sometimes wrong.
thanks
Dr. Decker
but I don,t found the results from independent methods or published from net
Try Perry' Chemical Engineering Handbook, that should have the data you need
you can use NIST data
I am looking for a way to analyze the results in the cloudsim simulator.
02 January 2021 1,192 2 View
Hi everyone I have a question about nanostructures modeling DFT? I have tow nanostructures X and Y, I wanna study of interaction of PEG 4000 and these nanostructures (X, Y) by DFT .But my problem...
06 December 2020 1,044 2 View
Hi everybody ; I have a question about the softwares used for calculating DFT of nanomaterials and nanocomposites? And the methods used for optimised this composites. regards
30 November 2020 9,601 4 View
Any suggestions on research topics on solar power and batter management system in an off grid system
22 September 2020 5,105 7 View
22 July 2019 4,650 1 View
what are the viscosity of urea and biuret at T=453k and P=162atm ???
01 April 2017 5,131 2 View
Polyoxometalate- XRD -Keggin structure
18 October 2016 9,451 1 View
I am looking for phospho-KIT (Y719) and total-KIT on mast cells using western blot.I can detect beautiful bands with phospho-KIT but it is impossible to detect total-KIT whatever I do! After...
06 June 2016 9,130 13 View
Does anyone know of any 'water treatment' solutions for alkalinity and hardness which make use of naturally occuring acids, to improve taste and increase usage of borehole/ tubewell supplies?
17 June 2014 5,777 5 View
I have heard so much about benefits of GMOs let's hear the other side for better decission.
04 September 2011 9,616 2 View
Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...
19 February 2021 472 5 View
All, I am trying to equilibrate an Ice 1h crystalline structure to 250K in LAMMPS. When I tried to do this at 250K directly, the structure lost it's crystalline shape and became disordered post...
14 February 2021 5,747 2 View
Hello, in my Aspen Plus Simulation (see attachment) there are two heat exchangers. One HEX1 (oil+gas) ist fed by hot gas which ist coming out of a burner. The other HEX2 (gas+gas) shall work as a...
14 February 2021 8,096 2 View
I have a box which is kept at 4C which is enclosed in a ziploc bag. The dimensions of the box are: 18cm x 13.4cm x 4.9cm. The relative humidity of this internal environment is 30% at this...
07 January 2021 6,734 3 View
Hello, my task is it to create a specific extraction process. There is a mixture containing water, nitric acid and hydrochloric acid. It is known, that tributyl-phosphate is a solvent, which...
03 January 2021 4,163 3 View
Dear Researchers, I am trying to model a gasification process for biomass on DWSIM. (Aspen plus is expensive and unreachable). I have been doing lots of searches but couldn't find anything. Is...
02 January 2021 842 4 View
Greetings, I am trying to run GROMACS 2020.3 on a supercomputer using this command to do the production run: mpirun -np 24 gmx_mpi mdrun -v -s AB_md_0_1.tpr -deffnm AB_md_0_1 >...
17 December 2020 1,232 3 View
For example, let's say if I design a conversion reactor and give inlet temperature,pressure,composition and reaction kinetics then Hysys will show me the outlet conditions. It doesn't,however,show...
09 December 2020 8,375 3 View
According to below articles about kinetic modelling of ODH reactions by G. Che-Galicia and et al. there are some problems need your guidance and advices: Kinetic and reactor performance of a...
27 November 2020 9,035 3 View
somebody, please elaborate on how to calculate exergy destruction in kW units. from Aspen HYSYS I found mass exergy with kJ/kg unit and i don't know how to calculate it by using Aspen HYSYS and if...
25 November 2020 2,675 3 View