I need Step by step procedure of doing dynamic analysis of spur gear pair in Ansys workbench?

More Vijay Kumar Karma's questions See All

How long will macrophages remain in the M1 state after treatment with 100 ng/mL of LPS?

In my experiment, I treated RAW macrophages with 100 ng/mL of LPS. After 24 hours, I collected the supernatant and replaced it with fresh media. I then quantified the cytokine levels of TNF and...

01 August 2024 476 2 View

What psychological factors contribute to the prevalence of obesity?

Psychological factors contribute to the prevalence of obesity

08 July 2024 6,124 2 View

How does excessive use of smartphones impact interpersonal relationships in contemporary society?

Excessive use of smartphones impact interpersonal relationships

03 July 2024 8,362 1 View

In what ways do economic factors influence family dynamics and relationships?

Economic factors influence family dynamics.

02 July 2024 6,235 0 View

Can u pls send me the conversion n selectivity formula for HPLC analysis?

please answer it quickly.

24 June 2024 2,256 2 View

What are the social factors that influence white-collar crime?

social factors that influence white-collar crime

22 June 2024 9,121 3 View

What Prevention Methods are Effective Against Teenagers Pregnancy?

Prevention Methods are Effective Against Teenagers Pregnancy

21 June 2024 6,321 10 View

What are the implications of mass media on social perceptions and behaviors?

Implications of mass media on social perceptions and behaviors

21 June 2024 8,265 6 View

How do the institutions of Family, Marriage and Kinship contribute towards the Socialization of young minds?

Institutions of Family, Marriage and Kinship contribute towards the Socialization

20 June 2024 7,056 4 View

Impact of overcrowded living conditions on mental health and social well-being in urban settings?

Impact of overcrowded living conditions on mental health

19 June 2024 8,713 5 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Maxim Naumov

If I understood the task description correctly, then I would suggest that you analyze the transients for dynamic effects. Additionally, you need to perform a modal analysis to exclude the phenomenon of resonance. If you can, please send me a general view of the model so that the recommendations are not abstract.

Vijay Kumar Karma

Dear Naumov, I have modeled spur gear in SolidWorks software. The gear parameters are module (3 mm), pressure angle (20 degrees), and number of teeth (20). Both the gears in pair are healthy gears. I have done transient static analysis using the Ansys workbench to determine transmission error and mesh stiffness for the pitch error case. Now I have to do the dynamic analysis to determine TE and mesh stiffness, but I do not know the steps to carry out the dynamic analysis correctly in Ansys. I am attaching the assembly of gears done in Solidworks.