I am interested to deposit zinc metal on ito glass. Please let me know the current and voltage to deposit zinc in two electrodes system?

More Binod Bihari Panda's questions See All

How to build a heterostructure of two materials having different space group?

How to build a heterostructure in VESTA/VASP of two pristine materials having different space group and structure?

27 July 2024 739 2 View

I found the zeta potential of exosomes in DLS and it was -8mv. So is it correct or not ?

What should be the zeta potential of bovine milk exosomes

25 July 2024 7,376 5 View

What are the possible chelating agents to form complex with cobalt only but not nickel in the solution of nickel and cobalt sulfate?

I want to electrodeposit cobalt only leaving behind the nickel in the solution

15 July 2024 3,462 2 View

Any Upcoming call for paper in journals ( SCI/SCIE indexed) related to image processing or computer vision related ?

Any Upcoming call for papers in journals (SCI/SCIE indexed) related to image processing or computer vision. Special issues related to my area, whose submission dates are within a few months.

23 June 2024 5,021 1 View

Can EBSD distinguish BCT martensite from BCC ferrite? Both have different symmetries, space groups but same lattice positions??

Electron back scattered diffraction is a versatile tool for micro-structure and micro-texture analysis of a variety of materials e.g., metals/alloys, rocks, meteorites etc., EBSD completely works...

18 June 2024 1,477 5 View

How to determine the (hkl) value of a novel polymer material?

I am working on a new polymer whose (hkl) values are not reported in the literature. How can I find out the (hkl) values of the XRD peaks?

17 June 2024 820 5 View

What method is good for doing in vitro degradation study of PCL microsphere by change in weight calculation or change in diameter (from microscope)?

I have prepared some polymeric microspheres from chitosan and PCL. However while performing in vitro degradation study, I found difficulties in both above mentioned methods. Here I am mentioning...

20 May 2024 6,114 4 View

How to increase the short circuit current density (Jsc) in a Cs0.15FA0.85Pbi3 perovskite photodetector?

Hello guys, I am optimizing a perovskite photodetector device with the device structure ITO/PTAA/Cs0.15FA0.85PbI3/PCBM/BCP/Ag. PTAA (2 mg/mL): 5000 rpm/30 sec Perovskite (1.3 M): 1000 rpm/10...

10 May 2024 2,297 0 View

Why intensity of XRD peaks corresponding to the filler increases with increase in filler loading?

What is the mechanism behind increase in the peak intensity with filler loading in polymer nanocomposite. In my work, the (014) peak corresponding to the filler increased proportionately with...

08 May 2024 7,972 3 View

Hello guys, What might be the reason for getting two PL peaks after deposition of PCBM onto Cs0.15FA0.85PbI3 perovskite?

18 April 2024 5,169 0 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

How to check pH of a high strength hydrogel?

We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...

30 July 2024 942 2 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Naima Ghemmit-Doulache

For the electrodeposition of zinc on glass in a two-electrode system and precisely on the cathode, you use low electric currents (low amperage), but the voltage can be quite high.

good luck!

Kiran Donthula

For three electrode setup -1.2 V is suitable for electro-deposition. May be you can try this voltage for two electrode.