For time critical traffic I want to minimize the queuing delays, I know the M/M/1 modeling etc but can anyone tell me a technique to reduce waiting times of packets in the queues whereas all the incoming traffic streams have equal priority.
I want a model that is balanced with accuracy or speed, faster rcnn has high accuracy while yolo have fast speed. i am thinking to combine them to get a hybrid model to achieve both speed and accuracy
02 August 2024 3,104 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
Hi everyone, I have extracted DNA from a biogas bioreactor using Qiagen kit and prep cDNA library then used this library as template to optimize primers for qPCR (taken from papers). Some of the...
23 July 2024 1,329 5 View
Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...
23 July 2024 4,925 1 View
Currently I need to calculate detection probabilities (PD) from RCS data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0 Equation. The idea is based on...
22 July 2024 2,851 0 View
Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?
22 July 2024 1,210 2 View
Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...
22 July 2024 868 0 View
Thanks
22 July 2024 1,143 3 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View