How to use membrane in ANSYS Fluent? Is these any built in function for membrane separation on the basis of permeability of a particular specie?

23 February 2022 0 5K Report

I am working on CFD analysis of membrane steam reforming reactor on ANSYS Fluent. I need guidance related to membrane function in ANSYS. If any one has experience of writing UDF for membrane flux please help me in this regard.

Badges
Science topic

More Khalid Saif Ullah's questions See All

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why the difference between degrees of nonclassicality of the input states is required for nonzero entanglement in the output state of a beam splitter?

By considering two single-mode Gaussian states at the input of a beam splitter, it is seen that the entanglement of the output two-mode Gaussian state depends on the difference between the degrees...

22 January 2021 3,490 3 View

What is the reason of weight gain in TGA curve of a HDPE polymer sample ?

HDPE samples were aged at higher temperatures in the presence of water and CO2 than the TGA test was performed in Nitrogen? Weight gain is seen in the curve? What could be the possible reason for...

16 January 2021 5,644 2 View

Hi Everyone. I want to conduct DEMATEL analysis for my survey. Everything is in line except the MAXIMUM MEAN DE-ENTROPY (MMDE) ALGORITHM. Need help ?

I can't find any manual or procedure on how to conduct the MMDE process. It looks like most of the literature has copy-pasted the stuff without any method of how to do to it. Any practical book,...

07 January 2021 1,804 2 View

What suitable boundary for stream function in inlets & outlets with COMSOL code?

As it has known the Dirichlet boundary condition is suitable for no-slip wall boundary for the stream function in COMSOL. I need to ask if I have an inlet and outlet I need to look for another...

02 January 2021 6,255 4 View

How to modify an article's "field of expertise" or "subspecialty"?

Greetings; I've recently published a preprint for a COVID treatment RCT, which appeared under "Dental" specialty instead of "Infectious diseases (ID)". This is an issue as it doesn't appear under...

14 December 2020 6,614 4 View

Does anyone have experience in infecting suspension cells (like THP-1 or K562 etc) by retrovirus?

I am trying to make stably expressing cell line of my gene of interest in Suspension cell line using retrovirus but i don't have recommended protocol. I have searched literature but mostly they...

14 December 2020 8,274 3 View

Hello I have a question about solar cells (perovskite solar cells) modeling in COMSOL?

I have done all optical simulations in RF module, now how can i find generation rate of electrons and holes, secondly how can i use these generation rate in semiconductor module to find further...

11 December 2020 6,652 3 View

Can a mathematical model be added to a paper on bean genetic and diseases manuscript?

10 December 2020 2,300 14 View

Straight chain or Ring peptide for inhibiting a homo-dimer of a 20 KDa secretory protein?

I am designing a small peptide to inhibit a homo-dimer of a small secretory protein (about 20 KDa). I need suggestions on, which option would be better? a straight-chain peptide or a ring-shaped...

03 December 2020 4,145 5 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View