Which heating methods do you recommend for establishing a poultry house (oil heater, gas heater, electric heater)?

I think a gas heater is better for the lower operating costs

03 January 2021 385 18 View

Do you think that the president in Iraq should be able to change the economic situation?

13 December 2020 7,193 3 View

Should I take sample from surface or subsurface for soil analysis?

I am currently doing my final year project on Geochemical analysis of peat samples. I will be looking at parameters such as major and trace elements plus anions and cations. Should i take samples...

27 November 2020 6,668 18 View

#Questionnaire, Big data?

Hello, i'm doing about using big data in telecom companies, but i need a questionnaire to measure big data using, can any one give information about that. thanks a lot, Nechirvan Othman Master...

20 February 2020 4,408 3 View

Saffranin and fast green Staining ?

I need to stain the stem of lily flower (semi-herbaceous). is their any commercial staining that can be used directly. Also, Is their any updated procedure or commercial product (mixture) of...

18 January 2020 3,769 1 View

What is best book to start study charge transport in organic semiconductors?

Could you suggest a good book or review articles on electrical transport and mechanisms in organic semiconductors.

17 December 2018 253 2 View

Can oxalate ion oxidaise V(IV) to V(V)?

Greetings I am engaged with the preparation of VO(II) complexes with the different bidentate amine ligands and the oxalate ion. The starting complex (NH4)2VO(C2O4)2 has been prepared by...

30 August 2018 2,028 6 View

Minirhizotron images data set for root?

Hello, I'm working on olive study and I'm using minirhizotron images to estimate root density in soil profile. However, the image analysis software provide an extra data such as, root surface...

19 November 2017 5,621 3 View

Aquapoinic culture system?

Hello, When we use the aquapponic culture system, does the water that come out from the fish tanks has all nutrients (Macro and micro) that the plant need or should we add some? Thanks

11 November 2017 3,224 4 View

Can we statistically control confounding variables using tests other than ANCOVA or regression?

can we statistically control confounding variables using tests other than ANCOVA or regression? specially in variables that violate parametric assumptions, for example if i am studying the...

22 October 2017 2,896 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View