How to start a model on homogeneous isotropic turbulence flow model in cp3d.How we get data first by using cp3d for this model?

last month 1 5K Report

How to start a model on homogeneous isotropic turbulence flow model in cp3d.How we get data first by using cp3d for this model.

Derrar Benamar Omar

I'm so sorry, I didn't use that code. Thank you.

Badges
Science topic

Similar topics
Eutheria
Rodentia
Muridae
Murinae
Mice

More Zawar Hussain's questions See All

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

How to retain amplicon yield after Ampure bead cleanup, following a 2-stage PCR protocol?

Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...

30 July 2024 841 2 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

How Can I Resolve a Persistent Unwanted NMR Peak at 1.25 ppm?

Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...

15 July 2024 9,065 4 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

What are the recommended rapid response scopus indexed journals in computer science?

Kindly provide their URLs. Thank you

30 June 2024 8,475 0 View

Is anyone who knows how to buy AMOS sofware?

I have been working in Hanoi University of Public Health. I would like to know where and how I can buy AMOS software?

28 June 2024 6,593 1 View

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

Cut PDMS sheet with Graphtec cutter plotter CE6000-40?

Dear All, I want to cut PDMS sheet with thickness of 0.8 mm to rectangular shape with Graphtec cutter plotter CE6000-40. What condition do you offer? Do you offer any kind of special speed or force?

25 June 2024 8,111 1 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Suggestions for the Annexin V Positive Control ?

Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...

29 July 2024 8,624 1 View

Why cannot i find my protein on cell surface after antibiotic selection of expressing plasmid?

I cannot confirm cell surface protein expression by flow cytometry even after transfection and antibiotic selection of cells. Does it take long for proteins to express on the cell surface? the...

28 July 2024 3,178 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

BD Cell Viability Kit - TO evaporation?

Hello, I'm conducting flow cytometry experiments using the BD Cell Viability Kit and I've noticed that the TO solution ends much faster than the PI solution. I store the solutions according to...

22 July 2024 2,257 0 View

Can I use CCCP instead of H₂O₂ as a positive control for ROS measurement through flow cytometry?

I am giving starvation stress to the soil amoeba (Dictyostelium discoideum) cells in my study groups and using NAC as a negative control. I am using DHE for ROS measurement.

20 July 2024 6,354 0 View

I came across oscillations in a pressure profile for a pipeline flow along the axis of a cylinder, how do I prove that these are not numerical err?

In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?

13 July 2024 6,296 5 View