How to report Moderated Mediation results using Process model 58?

More Muhammad Usman Shehzad's questions See All

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

How combine yolo with Faster R-CNN?

I want a model that is balanced with accuracy or speed, faster rcnn has high accuracy while yolo have fast speed. i am thinking to combine them to get a hybrid model to achieve both speed and accuracy

02 August 2024 3,104 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

How to retain amplicon yield after Ampure bead cleanup, following a 2-stage PCR protocol?

Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...

30 July 2024 841 2 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

Can I please ask why my samples from anaerobic bioreactor giving me different size PCR product even after multiple runs?

Hi everyone, I have extracted DNA from a biogas bioreactor using Qiagen kit and prep cDNA library then used this library as template to optimize primers for qPCR (taken from papers). Some of the...

23 July 2024 1,329 5 View

Swerling Characteristic functions?

Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...

23 July 2024 4,925 1 View

Radar Detection Probabilities?

Currently I need to calculate detection probabilities (PD) from RCS data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0 Equation. The idea is based on...

22 July 2024 2,851 0 View

Why methanol and sulphuric acid used in the analysis of polyhydroxyalkanoates (PHA) by GC-MS?

Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?

22 July 2024 1,210 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View